xIJoshF150Ix
New Member
- Posts
- 2
- Location
- Pickering
Hi Everyone -
Just after a bit of advice/where to look next. Me and my mate are doing up a TD5 we bought which was a non runner. I'm no stranger to TD5 having just virtually rebuilt my own however mines a manual and this is an Auto.
Now the M&S lights are flashing along with the D - I know that M&S can be low voltage so we've put a brand new battery on it which was fully charged, cleaned the terminals on the starter and up and the battery terminals, have adjusted the XYZ switch, have also opened it up and checked it all and cleaned it, Checked the Auto box Fluid Level, changed the gear inside the cab goes all the way to the 1st but the D light just flashes, had the negative cable onto a good earth in the engine and checked the wiring at the top of the gearbox and I can't see any breaks in any of the wires, it also had a new CPS before we got it and have check the wiring was a break and someone had knackered the multi plug and put new wires on and we've re done them.
I did plug it into my Code reader and all it comes up with is CAN Timeout Monitoring and CAN Level Monitoring but wouldn't read the Engine ECU.
I have tried the Reverse Wiper test (not sure how accurate it is) and the rear wiper works when I put the car in reverse. It cranks over but just won't start!
I am going to get some better sandpaper/wire brush tomorrow for the starter but before I get another XYZ switch is there anything else it could be that I'm missing?
Also have noticed that the Temp Gauge on the dash goes all the way up to the top and the overheat light stays on instead of staying on the cold like my manual does.
On another note we can't hear the fuel pump running when the ignition is turned on I have changed the relay from the one on mine (which works) still no good! Have checked the voltage which its getting 5 Volts. It had a new pump on before we bought it. I don't know what could cause this to happen.
Is there anything that I could of missed as were trying to desperately get it started!
Thank you
Just after a bit of advice/where to look next. Me and my mate are doing up a TD5 we bought which was a non runner. I'm no stranger to TD5 having just virtually rebuilt my own however mines a manual and this is an Auto.
Now the M&S lights are flashing along with the D - I know that M&S can be low voltage so we've put a brand new battery on it which was fully charged, cleaned the terminals on the starter and up and the battery terminals, have adjusted the XYZ switch, have also opened it up and checked it all and cleaned it, Checked the Auto box Fluid Level, changed the gear inside the cab goes all the way to the 1st but the D light just flashes, had the negative cable onto a good earth in the engine and checked the wiring at the top of the gearbox and I can't see any breaks in any of the wires, it also had a new CPS before we got it and have check the wiring was a break and someone had knackered the multi plug and put new wires on and we've re done them.
I did plug it into my Code reader and all it comes up with is CAN Timeout Monitoring and CAN Level Monitoring but wouldn't read the Engine ECU.
I have tried the Reverse Wiper test (not sure how accurate it is) and the rear wiper works when I put the car in reverse. It cranks over but just won't start!
I am going to get some better sandpaper/wire brush tomorrow for the starter but before I get another XYZ switch is there anything else it could be that I'm missing?
Also have noticed that the Temp Gauge on the dash goes all the way up to the top and the overheat light stays on instead of staying on the cold like my manual does.
On another note we can't hear the fuel pump running when the ignition is turned on I have changed the relay from the one on mine (which works) still no good! Have checked the voltage which its getting 5 Volts. It had a new pump on before we bought it. I don't know what could cause this to happen.
Is there anything that I could of missed as were trying to desperately get it started!
Thank you
