Could someone tell me what these are called please?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
tyclyd

tyclyd

Active Member
Posts
178
Location
Near Builth Wells
I ordered some rivnuts from Craddocks thinking they were the right parts but I need 3 of these to fit my rear mudflaps to the chasis of my 90 - could someone tell me what they are called or let me have a PN please?

Thanks - Gary
 

Attachments

  • Screw.jpg
    Screw.jpg
    17.8 KB · Views: 221
I think they're called captive bolts or something like that as I purchased some for my Landy a few years back.
 
Very similar to rivnuts, but ya don't need the tool to fit them ..

Rivnuts are probably much cheaper though and made of aluminium so won't rust..
 
You dont actually need the special tool for rivnuts but its probably better to use it. To do it without the tool put the rivnut in the hole and put a bolt with a nut on it in the rivnut (so the nut and bolthead are on the same side. Holding the bolt with a tommy bar or spanner to stop it turning (tommy bars better as its easier to keep things straight), turn the nut with a spanner so it tightens against the rivnut. Its easier with 2 people, 1 holding the tommy bar and one using the spanner Doing this bulges the rivnut out as it would with the special tool. This was how I put a new rivnut in my bulkhead for the fuel filter bracket to go on.
 
samc88 said:
You dont actually need the special tool for rivnuts but its probably better to use it. To do it without the tool put the rivnut in the hole and put a bolt with a nut on it in the rivnut (so the nut and bolthead are on the same side. Holding the bolt with a tommy bar or spanner to stop it turning (tommy bars better as its easier to keep things straight), turn the nut with a spanner so it tightens against the rivnut. Its easier with 2 people, 1 holding the tommy bar and one using the spanner Doing this bulges the rivnut out as it would with the special tool. This was how I put a new rivnut in my bulkhead for the fuel filter bracket to go on.
Click to expand...

Thanks I have a rivnut tool and a whole range of sizes but all too small for the haxagional holes in the rear crossmember... so i am a bit stuck?
 
tyclyd said:
Thanks - I have rivnuts but they are all circular - the chasis holes are hexagional?
Click to expand...

You could always run a drill through the holes to make them round to fit the rivnuts you have? Quicker than using a round file :)

Could you not use standard nut and bolt or is access too difficult? This is how it is on my series 3 but dont know how different it is on a defender
 
samc88 said:
You could always run a drill through the holes to make them round to fit the rivnuts you have? Quicker than using a round file :)

Could you not use standard nut and bolt or is access too difficult? This is how it is on my series 3 but dont know how different it is on a defender
Click to expand...

Did think about that but reaming out will mean that even my M8s will be to small and access fpor a normal M6 long bolt is not possible as you cannot get into the middle of the cross member...
 
You must log in or register to reply here.

Similar threads

A
Freelander 2 steering pipes / push fit or need a tool?
Replies
3
Views
374
Adam Fiander
A
jimllshiftit
Can anyone identify what these chassis' are, please?
Replies
16
Views
2K
Brown
Brown
dag019
Are all door latches equal?
Replies
2
Views
322
dag019
dag019
C
Hello, can someone tell me what I need to change to get rid of these errors? Thank you
Replies
7
Views
1K
pwood999
pwood999
Philgt50
Rear brakes TD4
2
Replies
26
Views
886
Philgt50
Philgt50
Back
Top