Clutch change completed, now having starting troubles. Suspect glow plug relay/circuit!

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
M

mellors89

Member
Posts
16
Location
Hull
Hi Guys,

Defender 90 300tdi did a clutch change over the bank holiday weekend.

Now it is having starting problems, we have never had starting issues before.

The defender was stood for four months before we did the clutch change.
We have mixed some fresh diesel in the tank, and also fully charged the battery.

When you turn the key, the starter motor cranks but it just doesn't catch. Sometime it catches a little but then dies, any suggestions?

Cheers
 
Removed the gearbox and transfer box. Used an engine crane through the drivers door and dropped it down and pushed back about 10 inches.

The only wires we touched are the main earth from the battery to the exhaust mount bracket.
Then disconnected the handbrake switch wire.
There was two wires connected the the gearbox on the drivers side, just a ring connector. I don't know what these are for but we put them back.

There was a plug that was already disconnected, i am guessing for the reverse switch as that never worked before.

I'm not sure if it cranks faster or slower to be honest, as its been stood a while.
We kept turning it over and starting it every couple of weeks whilst it was stood.

Any suggestions?
 
OK, so I had a quick look at lunch and I managed to get it to start.

I bypassed the battery earth cable (hooked up a jump lead from the battery to engine block)
This got it running.

After a few minutes I turned it off and it starts with the key like normal.

What I am guessing is because the engine has been stood a while it is struggling to start when cold as its not getting enough electrical power to the started motor. (I am guessing its a bad earth)
Once its warm it doesn't need as much power to start so even with the bad earth it is starting.

What do you guys think? Am I heading in the right direction?

The battery is only a few years old and it a Yuasa brand so should be up to the job.

Cheers
 
That'll be why JM was asking if it was cranking slower than before. But, as you say, hard to remember after that length of time. Once it's got some warm oil through all the moving parts it'll take a lot less current to turn and start it. Nice clean earth should sort it from cold.
 
Had another play with it the morning, cleaned all the earths up and got the multimeter out.

So when you turn on the ignition and wait for the glow plug light to go off, the voltage at the glow plugs is zero, then the light goes off and the voltage still stays at zero.

About five seconds after the light goes out the voltage comes back to 12.5v and the engine will be able to start. Still struggles a little.

I'm so puzzled! Any one got any suggestions?

Cheers
 
mellors89 said:
Removed the gearbox and transfer box. Used an engine crane through the drivers door and dropped it down and pushed back about 10 inches.

The only wires we touched are the main earth from the battery to the exhaust mount bracket.
Then disconnected the handbrake switch wire.
There was two wires connected the the gearbox on the drivers side, just a ring connector. I don't know what these are for but we put them back.

There was a plug that was already disconnected, i am guessing for the reverse switch as that never worked before.

I'm not sure if it cranks faster or slower to be honest, as its been stood a while.
We kept turning it over and starting it every couple of weeks whilst it was stood.

Any suggestions?
Click to expand...
there would need to be a main earth to the chassis usually the cross member top bolt and then earth cable to transfer box
 
You must log in or register to reply here.

Similar threads

A
Won't start - Jaguar relay on 1983 Defender 110 Perkins/Mazda 4.182
Replies
1
Views
892
Kev12
Kev12
Marc-Manchester
TD5 Starting Issues
Replies
6
Views
662
anitarrc
anitarrc
A
My hypo is not starting after alternator belt change
Replies
13
Views
2K
Al2O3
Al2O3
neilly
Disco 2 Hard starting then cutting out.
Replies
14
Views
3K
Simon098
S
Alibro
Clutch change in a TD4 (list of jobs to do)
2
Replies
30
Views
13K
NUM427F
N
Back
Top