Chassis repairs and rusty bits on Peggy the ex farmy pick-up

dag019 · Nov 13, 2023

Wagon Loon said:
Made pattern from recycled cereal box. Will leave putting holes in until new metal part fettled in place, I may have a piece of galv sheet that could do nicely, since this area is in a bit of a war zone; being immediately behind back wheel.
View attachment 302216Pattern should do other side flipped, as it's likely similarly punished!

Bit of underseal on that an I wouldn't have bothered with the effort of new metal would still hvae been better than mine when I bought it with 12months ticket.

Wagon Loon said:
I wondered why the mud flaps are not used to protect this area a bit more.

I had the same question but you can make your own to protect this area. I have just done this to mine and used come old conveyor belt I acquired from work to replace the foam rubber flaps that hang down from the rear tub to protect the rear lights. I simply cut new ones of these that were long enough to cover that part of the crossmember and bolted them to the original brackets. I also did the same with the front ones that come off the bottom of the mud shield in the front wing so the outrigger is covered.

Wagon Loon · Nov 14, 2023

Longer inner wheel arch mud flaps, good idea. As you say the original plastic sheet hangs too high to stop crude filling the crossmember, and with the visible mud flaps mounted behind, they only benefit vehicles behind, as far as I can see.
I will spray Waxoyl in the cavity and make sure water can drain freely once done. For me the regular removal of any collected mud and salt from the entire chassis is more important than cleaning the outside of a landy

Wagon Loon · Nov 14, 2023

Trying to cut the last bit of rot from O/S rear, which I found on Sunday. Couldn't do anything yesterday because of constant rain.
Using a thin cutting disc to get a good look pattern to work from. I couldn't see this from inside because it's double up metal, so was behind my internal view.

The part I want is still hanging on in a couple of places

But you can see some of the internal doubled up metal. I guess that's because it's where the spring supports the chassis.
Just waiting for the latest shower to stop shop I can get the rest of the piece out. So time fir a cuppa

Wagon Loon · Nov 14, 2023

Got it, and there's a doubled up parts top and bottom

Just trying to decide
1, Replace with one piece of 4mm metal
2, replace with two 3mm parts and cover with 2mm piece.

I'm kind of thinking to weld the two plates together inside

You can see on left of cut out. So it would be one piece inside, then weld a 4mm piece in to complete the repair.

LincolnSteve · Nov 14, 2023

Might it be best to avoid layers? One less place for water to creep in between.

Dr Strangeglove · Nov 14, 2023

Look at edge preparation on the thicker steel and the twin layer. You want to make sure you get both layers welded rather than just the top one.

Wagon Loon · Nov 15, 2023

I'll weld them together first before fitting a 4mm plate flush. The original combined thickness of 5.2mm was at the top and bottom, and 2.2mm in the center. So I'm hoping the 4mm plate I have a sheet of will be more than strong enough.
It's raining most of the time, but I can get it done in-between the showers. I didn't get the opportunity to do this when the weather was a bit better!
I'm looking forward to fitting the new wiring loom to the rear also, but am going to run it along the top of the chassis and can weld some securing brackets on to prevent any possibility of entanglement. It's handy being able to access the top of chassis under drivers seat too

dag019 · Nov 15, 2023

Wagon Loon said:
but am going to run it along the top of the chassis

You are already planning on doing it but this is the best piece of advice I could give anyone running a new rear loom. Wrap it in conduit for protection and run along the top of the chassis. much easer to repair/replace in future and no less protected. I have done it with both my 110 and series.

Dr Strangeglove · Nov 15, 2023

I replaced the rear section of my wiring loom but used a heavy duty 13 core trailer cable instead as I was going to have to join it anyway. Being 30 years old the loom was showing its age.

I considered a rear loom but chose the trailer cable as it had its own protective sheath, was good size wires and uses colours that are universal - not for the land rover purist but rugged! To further protect it I actually put a piece of quality nylon reinforced garden hose around it - I was going to use some of the split plastic conduit but actually found the hose fitted perfectly.

I then used a piece of the same trailer cable to make the loom to the other side light cluster and also to the trailer socket. They carry an earth but I have fitted a dedicated earth to the rear anyway.

Wagon Loon · Nov 15, 2023

I did buy a new loom from Sparks

Being the Pick-Up, it's the cheapest one having less going on. I did add an ignition powered cable for the caravan fridge and battery charging, which was further taped over with proper loom vinyl tape, and covered it all in corrugated plastic conduit, which I further vinyl taped over to keep water out.
So yes externally fixed to top of chassis leg is the plan.

Pattern cut

Marker the internal brace

Cut the part and drilled out where the brace is which I made bigger hole to weld through

Wagon Loon · Nov 15, 2023

After welding the layers together, I should have modified the card former. But I hacked Boris off the piece to get it to fit, so there was more space than needed

But it's welded in and thanks to a break in the weather and having just enough gas

If I clean it up a bit, it's good to paint and fit the new spring from Flatdog.

Wagon Loon · Nov 16, 2023

After cleaning up with flappy disc, painted over

The exposed metal with etch primer, and mixed some 2K paint

Thanks to it being dry, albeit a bit cold, was able to get some paint sprayed over the repaired areas to protect them; and before fitting a new spring and seat.

I had to warm the paint in the microwave to get it working with the hardener, but it's all shiny and black now

Wagon Loon · Nov 19, 2023

Got some new lights fir front. One was a fair bit milky on the chrome

Lots of cleaning up and cleaning contacts ect

Broken O rings had let a fair bit o muck into the repeaters

But they're looking lovely now
New O rings and bulbs too

Fitted a new bumper, same as factory, not even with the plastic corners. It took a little longer finding the earlier type.
Also got Night Breaker bulbs in now, but just plain white, not the ones with a blue tinge.
Been fitting the new loom also with many more zip ties than should be needed, but I don't fancy it getting round the prop.

I did use corrugated plastic conduit and it was also covered with vinyl loom tape as had to it a split to fit and the non sticky tape holds it together and should keep stuff out hopefully.

Knappster · Nov 19, 2023

Looking good.

Wagon Loon · Nov 20, 2023

Thank you,

All the lights work and look original even if the front lights have night breaker bulbs

It's the details, when thinking on what's to do, forget the details like for me bump stop to be mount, but it's on now

The black paints so shiny, can see my orange Overalls.

Tie off the loom where it goes up into the tub, and making sure no sharp edges to cut through cable ties .

tottot · Nov 20, 2023

If only Land Rover had wired them like that in the first place.

Wagon Loon · Nov 20, 2023

That would make repairing the chassis a bit easier lol

Here are my favourite bits of paint patina on the car from elbows hanging oot, and legs getting in and oot

Wagon Loon · Nov 20, 2023

I just kept the original flap

dag019 · Nov 20, 2023

Wagon Loon said:
View attachment 303079
I just kept the original flap
View attachment 303080

I still think you should make an extended version to protect all of the hard work you have just put into the crossmember and have the rubber flap come down to the bottom edge rather than just cover the ali tub which does not rust!

Wagon Loon · Nov 20, 2023

That's still a possibility,
I will be revisiting the chassis quite a bit and need to get back to using her as well as continuing round lots of small and medium jobs.
Like replacing the fuel filler neck which has a small rust hole and the rubber and seal + lock barrell in cap

I think your idea is a good one, and I may use an old 20 L oil container as the sides are tall and flat.

Chassis repairs and rusty bits on Peggy the ex farmy pick-up

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads