Chassis repairs and rusty bits on Peggy the ex farmy pick-up

Wagon Loon · Nov 9, 2023

Recently bought 90 300 TDI Pick-Up.
My needle descaler is very good at unhiding rust perforations and hidden holes. These can look solid under crusty layers of metal and paint.

From under O/S/R spring top mount.
I removed the spring, which am replacing with new Flat Dog standard springs, galv seat and ss bottom clamp bracket.
The bump stop was missing and the bump stop mounting bracket heavily corroded in the middle where it contacts the underside of chassis leg.
So bracket cut off and a longer section of bottom cut out with plasma cut into good metal.
Pic above is new part/original part.

This got fully pushed together and mig welded in last night after rain stopped, and I'd sprayed rust treated inside accessible chassis. Got a powerful led on helmet which really helps.

Brown · Nov 9, 2023

That's pretty neat welding considering it's upside down.

Wagon Loon · Nov 9, 2023

Thanks,
Need to grind it down to tidy up and get the new bump stop mount on

So it's time to wake up any late sleeping neighbours with my flappy disc on grinder

miktdish · Nov 9, 2023

Nicely done ... and so it begins

Wagon Loon · Nov 9, 2023

Indeed lol
Rear crossmember is great outside, has been replaced

But been driven in salt, full of muck and never cleaned on the inside, so some rust jacking has occured and I need to work on the inside part to make it more happy

Rust treated and etch primed ready to weld the bump stop bracket on

I will mark and clean back to bare metal at the weld points. That log is perfect to hold bracket in place

Wagon Loon · Nov 9, 2023

Got the inner part out intact, cleaning and will treat outer, and make a new inner to weld back in with fresh metal

Time for the old cereal card to make a pattern

Wagon Loon · Nov 10, 2023

Made pattern from recycled cereal box. Will leave putting holes in until new metal part fettled in place, I may have a piece of galv sheet that could do nicely, since this area is in a bit of a war zone; being immediately behind back wheel.

Pattern should do other side flipped, as it's likely similarly punished!

tottot · Nov 10, 2023

Last year did some repair on mine, mud flaps on the inside have kept the cereal box area good on mine. Rot was in the area of the tube jacking points that I never use so I removed them [real crud traps]

Wagon Loon · Nov 10, 2023

tottot said:
Last year did some repair on mine, mud flaps on the inside have kept the cereal box area good on mine. Rot was in the area of the tube jacking points that I never use so I removed them [real crud traps]

I wondered why the mud flaps are not used to protect this area a bit more.
Is that a 13 pin towing socket by your fog light?
I've got a new rear loom and have a tow socket to fit, once the welding is done.

Wagon Loon · Nov 10, 2023

Here's hoping,

Got some nice galv 2mm sheet which should do. Been using 3mm on the chassis leg.
I'll keep the jack tube, since have original jacking kit and like factory.
However do use a farm jack on Gigi the 1975 S3.

Wagon Loon · Nov 10, 2023

Just some tidying up and folding

And cutting two, one fir other side

I always use respirator, especially with galv metal

, and the wee plasma cutter is a great bit of kit

tottot · Nov 10, 2023

Original jack was something I chucked in the corner after using it once, saw its rusty remains a few years ago. [In my top ten of rubbish things I have owned]
Trailer socket is just a standard 7 pin fitted in an out of the crud position. Mine is a working truck so practicality comes before originality.

Wagon Loon · Nov 10, 2023

tottot said:
Original jack was something I chucked in the corner after using it once, saw its rusty remains a few years ago. [In my top ten of rubbish things I have owned]
Trailer socket is just a standard 7 pin fitted in an out of the crud position. Mine is a working truck so practicality comes before originality.

Lol, haven't actually used jack yet. Maybe it is useless!
Cutting a new holder for the 13 pin socket I use fir towing my caravan.
Mine needs to be in the original position for my cable to reach.

Got some 3mm scrap will do. The 13 pin socket is much more weather proof than the 12N 12S ones used to be. I'm only off-road in my small woods so hopefully it will hold out, or I may take your idea with a small extender cable.

Wagon Loon · Nov 13, 2023

Managed to get the galv part I fabricated welded in yesterday, just before the rain started again!
Small dogs on the hunt for mice

I will tidy the welds up a bit, when weather permits, and found another small area needs sorting on the inside of chassis leg, which I'd missed. But now's the time to do it, while the springs out. It's above the bump stop mount, which isn't welded in that side yet.

miktdish said:
Nicely done ... and so it begins

Indeed

tottot · Nov 13, 2023

Nicely done, couple of pics of my 1990 chassis [owned since 93] It has only needed small bits of welding in that time, odd bits of corrosion in those exposed area's. Sprayed every year inside and out with oil and diesel mix.
Before I had a series that had been in the sea, chasing rust was quite a pass time.

Knappster · Nov 13, 2023

Good repair.

KISSMYAURA · Nov 13, 2023

Wagon Loon said:
Made pattern from recycled cereal box. Will leave putting holes in until new metal part fettled in place, I may have a piece of galv sheet that could do nicely, since this area is in a bit of a war zone; being immediately behind back wheel.
View attachment 302216Pattern should do other side flipped, as it's likely similarly punished!

great to see you using LR original quality plate in this picture

Turboman · Nov 13, 2023

KISSMYAURA said:
great to see you using LR original quality plate in this picture

I should think a cereal box is much better quality than what Land Rover used.

Or maybe you mean the metal?

Wagon Loon · Nov 13, 2023

I'm slowly restoring a1982 Series 3 Station wagon. Recreated most of the front. But I've noticed many of the parts replaced, like out riggers have gone to tin worm more quickly than the original metal.

She's a 12 seater, and I've restored the bulkhead already.

It's in Raptor primer and lives inside for now.
But I've come to the conclusion that the metal of many replacement parts may not be that great.
Plus I may enjoy making a rod for my own back !
But most of the 90's chassis is really good considering how much farm muck it had eaten

She's now had an enema, courtesy of a drain cleaning attachment on the pressure washer. Much compacted stuff removed, and the rust is were muck had accumulated and sat damp, no doubt salted to taste, to aid the tin worms digestion!

Wagon Loon · Nov 13, 2023

The fabricated galvanised part

Is definitely better than the original part of a replaced rear crossmember.

I made the towing socket bracket from a scrap 3mm steel piece, which took a bit of fettling.

And I coded the 13 pin wires to the Landy colours and fitted Lucas brass connectors; which will connect to a new rear wiring loom made by Sparks in England.

Chassis repairs and rusty bits on Peggy the ex farmy pick-up

Well-Known Member

Well-Known Member

Well-Known Member

Guns n Chainsaws

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Attachments

Well-Known Member

Well-Known Member

Mab An Gov

Well-Known Member

Well-Known Member

Similar threads