CAV problem

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
F

Faber

Member
Posts
53
Location
Berks
The inner part of the hydraulic head of my 1980 Series 3 diesel rotates freely when it is out of the body but when I replace it, mating with the spindle, it just moves a bit then stops. I imagine that the whole device from spindle to head should rotate easily but I cannot think of what is stopping it. Any explanation or advice as to how to rectify the fault greatly appreciated.
 
Thanks Steve. I'll try to include a picture of the head. It is the central bit with the vanes which should rotate freely At least I assume it should and I don't want to find that I put it on the LR and the quill or something else breaks.
 

Attachments

  • Top with vanes.jpg
    Top with vanes.jpg
    230.3 KB · Views: 115
CharlesY would have known the answers but not been on here for a few years now, you can search on here to see what’s been asked previously, I did find a post saying the vanes only go in in a certain way,
I assume you can turn the bottom shaft freely that works of the camshaft without the vanes in but not with the vanes connected?
 
Agreed, check the centre spins without the vanes in then double check how you have the vanes.
Attached is manual.
.
 

Attachments

  • CAV Workshop Manual fuel-injection-pump.pdf
    3.9 MB · Views: 116
steve2286w said:
CharlesY would have known the answers but not been on here for a few years now, you can search on here to see what’s been asked previously, I did find a post saying the vanes only go in in a certain way,
I assume you can turn the bottom shaft freely that works of the camshaft without the vanes in but not with the vanes connected?
Click to expand...

Even without the vanes it will move only a fraction - about the travel of the bolt in the ring on the advance retard device.
 
Just checked mine which is on the bench and the bottom drive spins easily, have you had a search on you tube
CAV DPA pump brings a few videos up
 
if i the hydraulic head turns whilst it is removed as an assembly but will not turn when installed it must be the pumping plungers and or shoes/rollers are stuck
 
  • Like
Reactions: 8ha
adrian hogg said:
if i the hydraulic head turns whilst it is removed as an assembly but will not turn when installed it must be the pumping plungers and or shoes/rollers are stuck
Click to expand...
Thanks Yes This is the conclusion I've come to from having a look at diagrams, but I am wary of dismantling lest I upset the calibration. Any suggestion s as to how to do this without cocking everything up would be greatly appreciated.
 
Once the head and rotor assembly is removed from the pump body you can unscrew the cross rotor that turns the blades in the transfer pump then slide the rotor assembly out of the hydraulic head. Find a piece of steel which is a good fit in the slots (at a push you can use the oval side plate off the pump but make sure you insert it as deep as poss into centre of slots and turn with a good adjustable spanner big enough to hold the full width of plate as close to the transfer rotor as poss. and hold the rotor across the two bi-hex pins in a soft jaw vice Be careful as the SHOES CAN BE PUT IN BACK TO FRONT they contact the fuel adjuster plates in the max fuel position with a concave profile
Dirt even in tiny amounts is your enemy if you dismantle the rotor from the head, running clearances are only a couple of microns so nothing abrasive is welcome especially if trying to clean parts use copious amounts of clean diesel or paraffin. I will gladly talk you through it if you send me a pm Iwill give you my mobile number
 
Pistons could be gummed, if so worth trying some penetrating oil. If there's a tiny bit of corrosion I have polished out with brasso but as said above, dirt is your enemy.
 
Thank you both very much for your advice. I'll have a look at it tomorrow and see what I can do. Thanks for the offer of a phone call. The problem is I am rather deaf and cannot hear anything on the phone so if you don't mind I may contact you again when I get stuck.
 
I forgot to add, if its ever been run on biodiesel or veg oil and there are traces in the system it really gums up these pumps.as they are fuel lubricated with tiny clearances. The veg oil sets if left standing - it polymerises over time - and will completely glue the moving parts together. Penetrating oil and some heat will get the parts to move, once moving you can flush it out.
 
Thanks. I have never run it on Biodiesel despite attempts by a farmer friend to sell it to me cheap!
 
Thank you everyone for your help. I removed the slotted top bit and seeing that the plungers were seized tried to tap them out with a chop stick. This didn't work so I made a couple of short dowels out of hard wood and both popped out. I've cleaned them up, bathed them in diesel and put them back. Everything now rotates freely.
 
You must log in or register to reply here.

Similar threads

mjr92
Horn and flash problem
Replies
12
Views
588
mjr92
mjr92
M
2007 L322 4.2l v8 (Misfire cylinder)
Replies
4
Views
822
stuu
stuu
Y
Freelander 2 (LR2) 2013 SD4 auto rev drop (solved)
Replies
9
Views
648
Yampy
Y
O
How to get exhaust and turbo off 200tdi
Replies
5
Views
836
dag019
dag019
O
Defender 90 300tdi difflock not doing anything
2
Replies
29
Views
2K
marjon
marjon
Back
Top