Can't shift IRD filler nut, car on ramps, difficult

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
O

Oldschool2

New Member
Posts
9
Been trying to remove my IRD's filler nut to first check the level and potentially drain and change. Bloody nightmare, I'm attempting this with the the front of the vehicle on ramps and can't get in a good enough position to get my full weight into it. Any ideas or tips I might be missing?

I have been using a hex socket and tried with wrench, extended wrench and t bar but still can't get enough pressure on it, awkward position.
 
Cheers, that's a good idea about the block of wood on the frame, will give it a go and post my results.
 
It's only a filler plug ffs with a sealing washer to boot.
No one in their right mind would even tighten a drain plug up that tight, it's not as though there is serious pressure inside !!:eek:
When you refit it, just tighten it as you would a sump plug and don't use any thread sealer (Loctite etc.)....it aint going to loosen and fall out.
 
I found the IRD filler plug can be a bastid to get oft. Even when it's tightened to the recommended 35Nm it's hard to get oft. It sits flat against the IRD (and slim copper washer) and when you undo it it suddenly snaps loose. Pic below of the IRD filler bolt.

P2271826a.jpg
 
Did mine , had the same chew , 6 sided socket , a block of wood and a mate to keep the bar/socket strait on the plug , had to replace the plug/washer , second time ive done it , and the plug was not tightened to that extream :eek:
 
Mine was not to bad , Used a 6 sided socket & swivel head wrench angled forward to clear chassis , A hit with plastic hammer and it came undone :)
 
Irishrover said:
It's only a filler plug ffs with a sealing washer to boot.
No one in their right mind would even tighten a drain plug up that tight, it's not as though there is serious pressure inside !!:eek:
When you refit it, just tighten it as you would a sump plug and don't use any thread sealer (Loctite etc.)....it aint going to loosen and fall out.
Click to expand...

I have only had the vehicle a month so i don't think it has ever been off. No record in the paperwork and I have all the history.

Cheers
 
Hippo said:
I found the IRD filler plug can be a bastid to get oft. Even when it's tightened to the recommended 35Nm it's hard to get oft. It sits flat against the IRD (and slim copper washer) and when you undo it it suddenly snaps loose. Pic below of the IRD filler bolt.

P2271826a.jpg
Click to expand...

Deffo the bolt in the photo, same as Haynes photo

Cheers
 
Sounds like a galvanic reaction seizing the steel bolt in the ally hole.

I take it the bolt underneath it at the bottom of the pic is the drain plug? Gonna do mine soon. What oil is recommended? What about the manual gearbox too? Anyone got pics of the plugs and oil recommendations?

Ta!
 
You must log in or register to reply here.

Similar threads

Cornishdefender
Help - Gear box oil filler plug rounded off
2
Replies
26
Views
4K
Cornishdefender
Cornishdefender
S
Defenders Vs Insurers tomfoolery
Replies
1
Views
3K
lightning
lightning
Tango91
  • Poll
Disco 2 Things I wish I knew when I took the body off (99 D2 TD5)
Replies
8
Views
3K
FlatbedPilot
FlatbedPilot
Rob4x40
L322 TD6 transmission adventures
Replies
13
Views
3K
badfluffy
badfluffy
Caseymi
IRD Filler plug
Replies
7
Views
1K
Rich in Vancouver
Rich in Vancouver
Back
Top