GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Bugger !!
- Thread starter GrumpyGel
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Diesel Do
Well-Known Member
- Posts
- 5,213
- Location
- Nottingham
Ha ha 
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Thanks for the sympathy bro :Cry:
englishbullterrier
Active Member
- Posts
- 824
Ha ha
Seconded :mil77:
tonytherunner
Active Member
- Posts
- 339
- Location
- wherever the road takes me
...good luck
baptista
Active Member
- Posts
- 678
- Location
- Lisbon, Portugal
engine runs + full tank = OK
Hub
Active Member
- Posts
- 450
- Location
- Along the embankment
My sympathies
blackstrat
Well-Known Member
- Posts
- 9,265
- Location
- East Anglia
There is a positive.. your dash lights work fine..
Silverlandy
3.5efi's other half
- Posts
- 5,707
- Location
- Suffolk
You have my sympathy grumps. If mine did that at this moment in time it would be as welcome as a fart in a spacesuit
Epicuser
Ex Freelander Owner
- Posts
- 2,393
- Location
- North East Surrey
Oh well.
At least you know what to do......
At least you know what to do......
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Yeh, curse the 5 quid ODB2 reader for not working !
Last time it was the modulator - so got a replacement one fitted. I kept the old one though cos I read there is a 'bodge' you can do to them so they work again - something to do with routing a wire through its internals or something - I'll have to dig that out again.
Anyway - first thing is to get it down a garage to have the codes read - or invest in an i930.
Oh and apart from those couple of kind souls - bollocks to the lot of you !
Think I'll post it on the FB page for some group hugs
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
As I said in the last post, you are all wonderful people and before spending out having the codes read, I was thinking....
When I turn the ignition on, I get the 4 lights (ABS, TC & 2xHDC lights). One of the HDC lights goes out to leave the three lit and they stay on. This is before I move the car. Normally, I think 3 go out to leave just the ABS lit - and this goes out once up to about 5MPH.
So from this, can I safely say its not a wheel sensor/drive shaft ring - because these only are identified once the car is moving? Or is there a 'self check' on the sensors?
I can also safely say its not the brake switch - because that doesn't throw the TC light.
So by deduction - it must be the modulator?
When I turn the ignition on, I get the 4 lights (ABS, TC & 2xHDC lights). One of the HDC lights goes out to leave the three lit and they stay on. This is before I move the car. Normally, I think 3 go out to leave just the ABS lit - and this goes out once up to about 5MPH.
So from this, can I safely say its not a wheel sensor/drive shaft ring - because these only are identified once the car is moving? Or is there a 'self check' on the sensors?
I can also safely say its not the brake switch - because that doesn't throw the TC light.
So by deduction - it must be the modulator?
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Yeh, brake lights are OK.
teddywood1
Well-Known Member
- Posts
- 5,558
- Location
- stoke-on-trent
sorry to hear you have the dreaded problem,have you checked the gravity sensor that is next to the handbrake under the centre console .
spannerspencer
New Member
- Posts
- 28
even if brake lights work, it still could be the brake light switch. ive had 3 go. and each time its been one of the three gold prongs snapped off inside at the bottom of the switch causing it to short.
GrumpyGel
Well-Known Member
- Posts
- 26,393
- Location
- Christchurch, New Zealand
Yes, agreed - it needs the codes read.
You don't say which god you're going to pray to. Is he/she any good with the spanners?
You don't say which god you're going to pray to. Is he/she any good with the spanners?
