Brake lights not working right

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Quillia

Quillia

Member
Posts
27
Location
suffolk
Quillia Good evening, been outside with torch blazing !!! Need help to to find problem with brake lights???
Here is my dilemma... brake switch brand new, set properly works fine. Lights are all new but problem still persists.
Then I turn lights on and brake lights do not work! Or are on as the tail lights are brighter?
Would be greatful for any advice. All bulbs are in correctly. Everything thing was good and then problems. Before I changed lights this problem occurred! If earthing please tell me good remedy to follow to diagnose fault.
Thank you
I have a 92' Land Rover 110 na 2.5d ex-mil
Regards
 
Have cleaned earth connections rear but still cross feeding! Good suggestions are needed not sarcasm thank you
 
Quillia said:
Quillia Good evening, been outside with torch blazing !!! Need help to to find problem with brake lights???
Here is my dilemma... brake switch brand new, set properly works fine. Lights are all new but problem still persists.
Then I turn lights on and brake lights do not work! Or are on as the tail lights are brighter?
Would be greatful for any advice. All bulbs are in correctly. Everything thing was good and then problems. Before I changed lights this problem occurred! If earthing please tell me good remedy to follow to diagnose fault.
Thank you
I have a 92' Land Rover 110 na 2.5d ex-mil
Regards
Click to expand...
are you saying brake lights work fine till you switch tail lamps on, brake light filament should be the brightest,
 
Bulbs in wrong, bad earth, wire interchanged, tail for brake etc, dodgy towbar electrics, wiring chafed where it enters or leaves chassis are all places to look
 
Yes that is correct once tail light on brake light is also on. As no change in brightness when brake pedal depressed.
freelance said:
Bulbs in wrong, bad earth, wire interchanged, tail for brake etc, dodgy towbar electrics, wiring chafed where it enters or leaves chassis are all places to look
Click to expand...
cheers have looked all wiring seems good! All sheafs good no obvious signs any ideas? Apart from stripping sheaf from wires and checking for hot spots (burns)
It just happened no warning! Fuses are all good
 
Quillia said:
Yes that is correct once tail light on brake light is also on. As no change in brightness when brake pedal depressed.

cheers have looked all wiring seems good! All sheafs good no obvious signs any ideas? Apart from stripping sheaf from wires and checking for hot spots (burns)
It just happened no warning! Fuses are all good
Click to expand...
bad earth ,from lamp unit ,run a fresh wire from lamp to the body
 
Quillia said:
Quillia Good evening, been outside with torch blazing !!! Need help to to find problem with brake lights???
Here is my dilemma... brake switch brand new, set properly works fine. Lights are all new but problem still persists.
Then I turn lights on and brake lights do not work! Or are on as the tail lights are brighter?
Would be greatful for any advice. All bulbs are in correctly. Everything thing was good and then problems. Before I changed lights this problem occurred! If earthing please tell me good remedy to follow to diagnose fault.
Thank you
I have a 92' Land Rover 110 na 2.5d ex-mil
Regards
Click to expand...
Your username and avatar picture look familiar. Are you on another forum?
It is a little tricky to decipher the situation. But, Ignition on and all lights off, foot on brake and brake lights come on. Put lights on and when you put the brakes on you can't tell if the brake lights are coming on. Either they are not, or the tail lights are so bright you can't tell they are on. Is that it?
 
+1 wot @jamesmartin said.
People will often say that all the wiring is good, and that might be the case. However, very often the fault with twin filament lights is with the earth connection between the silver body of the bulb and the earth contact inside the bulb holder.
Clean the inside of the bulbholder with a bit of emery cloth and if necessary give the contact a bit of a tweak to try to improve the connection.
 
THank you will do and let you know
Stay well
Al2O3 said:
Your username and avatar picture look familiar. Are you on another forum?
It is a little tricky to decipher the situation. But, Ignition on and all lights off, foot on brake and brake lights come on. Put lights on and when you put the brakes on you can't tell if the brake lights are coming on. Either they are not, or the tail lights are so bright you can't tell they are on. Is that it?
Click to expand...
 
Cheers RR PROBLEM FIXED brake light feed on trailer loom sheared by rear crossmember up by fuel tank! Cleaned dried mud and found insulation charred and copper on copper cross feeding and interfering with pick-up combined lights.
To much expo mayb
Regards Quillia
 
You must log in or register to reply here.

Similar threads

D
Tail lights not working
Replies
2
Views
188
miktdish
miktdish
R
LED side lights not working
Replies
9
Views
722
RickyFreelander
R
J
Landrover Discovery 4 - Brake light not working
Replies
6
Views
1K
Graculus
Graculus
G
Freelander 2 brake lights not working
Replies
3
Views
799
WhiskyLassie
WhiskyLassie
G
Freelander 2 brake lights not working
Replies
0
Views
572
Gethpd
G
Back
Top