border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Brake Calipers
- Thread starter border
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
bolt too long ?is caliper central
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
I remember when I bought the bolts there was 2 different sets, I'm sure I posted thread on here about them, will try and find it. first one was wrong thread so got these ones, they go in perfect but like mentioned probably to long. What's the options will washers do ?
Last edited:
Do they have washers? A Manual I have shows spring washers.
If so I would just be inclined to take a file to the end and shorten them its obviously only a very small amount.
Are they new discs? The bolts aren’t just going into some rust build up on the discs somewhere?
J
If so I would just be inclined to take a file to the end and shorten them its obviously only a very small amount.
Are they new discs? The bolts aren’t just going into some rust build up on the discs somewhere?
J
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
fine thread bolt not coarse thread bolt does have a spring washer
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
I'm certain they are the right bolts, will try spring washer. Thanks
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Mines same as top Thank You
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
m12 spring washers
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Thanks Again, couldn't find any out of the bucket full of old nuts and bolts I have, will get some tomorrow.
13 mm fits not sure if its the right one
but it fits.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
its right but when corroded over time a 1/2 inch fits betterThanks Again, couldn't find any out of the bucket full of old nuts and bolts I have, will get some tomorrow.
13 mm fits not sure if its the right one
Flossie
Well-Known Member
- Posts
- 11,001
- Location
- Shropshire
Multipoint 1/2 af socket and the same size ring spanner works well. They need tapping on to the bolt head but they have never slipped on me, 13mm has though.
Get quality ones though, mine are both britool.
Get quality ones though, mine are both britool.
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Well this has got my head done in now. The bolts were coming through and catching disc to stop it spinning fix i could see them. Put washers on , not coming through now But now the are catching side of hub, when fully tightened so no further forward. Think I'm Jinksed
Attachments
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Have not got a clue Mate they were in box of parts that came with it when I first bought it,
Hmmm...might be the wrong ones.
Anything stamped on the reverse face that looks anything like this?
Not saying this the right Caliper for your project, but there are various iterations of Caliper on 110 axles over the years....
https://www.lrworkshop.com/diagrams...ms-discs/front-brake-calipers-and-discs_52911
Anything stamped on the reverse face that looks anything like this?
Not saying this the right Caliper for your project, but there are various iterations of Caliper on 110 axles over the years....
https://www.lrworkshop.com/diagrams...ms-discs/front-brake-calipers-and-discs_52911
border
Well-Known Member
- Posts
- 3,517
- Location
- North East. UK
Couldn't find any numbers on them, but was thinking they could be wrong ones myself. Mind you they are only catching Very slightly, but then again enough to stop the hub spinning.
