G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
a 2" body lift will be better than a 4" suspension lift
Body Lift
- Thread starter newson
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
a 2" body lift will be better than a 4" suspension lift
- Posts
- 83,282
- Location
- Embasinga stocæ
Still wont stop yu getting stuck tho - ground clearance will still be the same.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
aye but will keep the centre of gravity down and stop the tyres hitting the body allowing better articulation
the body lift i did was on a bobtail that was already +2" on suspension with 35" tyres
wiltshire landyman
I’m back
- Posts
- 15,062
- Location
- salisbury plain wiltshire
my rr bobtail has a 4" lift using lift kit and spacers and a 4" body lift
36/12.50/16 simex
everything else associated with a lift has been done
this handles way better than my defender ever did
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
for a 4" lift you need 6 degree radius arms, double cranked trailing arms, couble cardian prop shafts, custom extended brake hoses, lowered shock mounts, extended shocks and a host of other parts
pretty easy it took me half a saturday to do the lift, the main problem i encountered was the steering column crush joint (from the bulkhead part of the column to the UJ at steering box needed to be 1/2" longer but an early one solved the problem as the splines are different (longer splines)
- Posts
- 83,282
- Location
- Embasinga stocæ
Brake hoses?
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
have a look on wizardbilt.com
wiltshire landyman
I’m back
- Posts
- 15,062
- Location
- salisbury plain wiltshire
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
give them a ring, they normally sell through ebay so the products link to an ebay listing
its a family business and they are nice people, i have spoken to them a few times
its a family business and they are nice people, i have spoken to them a few times
battenberg
Well-Known Member
- Posts
- 2,101
- Location
- Birmingham UK
i've done a body lift on my 300. 'cos i wanted the height to accomodate bigger tyres without altering the suspension geometry
first wash the under side, you'll be cursing if you spend the day with crud dropping in your face trying to shift bolts.
the seatbelts all mount to the chassis, the clevis pins under the boot floor are the most problematic as access is restricted and it's hard to get a torch in there if you need to burn them.
the transmission tunnel rubber gaiter will need to be drilled out or run the risk of damaging it. check it is in tact or buy a second one, and canabilaise the first one to create a seal gasket for the top of the gearbox. do this before you go wading again!
you will need a friend with a lathe to make you some radiator mount extensions, and a gear lever extension for your transfer box. dont expect your gear levers to work correctly until you've moved the positions of the gaiters very slightly, i had to dremmel out the center console and move the gaiters backwards.
be prepaired to cut the bolts off or torch them on every mount. out of the 10 bolts that hold the body to the chassis only 1 came away clean without heat or grinder.
expect your steering to feel a bit wierd, the extra travel on the linkage puts a slight new angle on the UJ's and forces a noticable center spot in the steering , check the power steering resevoir the uplift may stress the hoses.
check the fuel lines to your fuel filter from the lift pump, they may be over stressed by the lift. (my mates sheared due to this, but then he had just decended chapelgate, which is enough to break most cars)
fit extended brake lines.
altering the bumper height... i havent botherd, but did need to modify my rear heavy duty bumper slightly by cutting out to make it fit .
first wash the under side, you'll be cursing if you spend the day with crud dropping in your face trying to shift bolts.
the seatbelts all mount to the chassis, the clevis pins under the boot floor are the most problematic as access is restricted and it's hard to get a torch in there if you need to burn them.
the transmission tunnel rubber gaiter will need to be drilled out or run the risk of damaging it. check it is in tact or buy a second one, and canabilaise the first one to create a seal gasket for the top of the gearbox. do this before you go wading again!
you will need a friend with a lathe to make you some radiator mount extensions, and a gear lever extension for your transfer box. dont expect your gear levers to work correctly until you've moved the positions of the gaiters very slightly, i had to dremmel out the center console and move the gaiters backwards.
be prepaired to cut the bolts off or torch them on every mount. out of the 10 bolts that hold the body to the chassis only 1 came away clean without heat or grinder.
expect your steering to feel a bit wierd, the extra travel on the linkage puts a slight new angle on the UJ's and forces a noticable center spot in the steering , check the power steering resevoir the uplift may stress the hoses.
check the fuel lines to your fuel filter from the lift pump, they may be over stressed by the lift. (my mates sheared due to this, but then he had just decended chapelgate, which is enough to break most cars)
fit extended brake lines.
altering the bumper height... i havent botherd, but did need to modify my rear heavy duty bumper slightly by cutting out to make it fit .
Last edited:
Similar threads
Disco 4 (LR4)
2016 DISCO 4 sdv6