P38A Ball joints

frostythor · Aug 9, 2020

and I downloaded the manual from this site

https://docs.google.com/viewer?a=v&...GFuaWN3b3JsZGNsdWJ8Z3g6NzBmNTI5OWU0MDY0OWEwMg

pete12345 · Aug 9, 2020

Thanks very much for the assistance I think it will press out now that nut stays in place for the hub alignment there’s no need to remove it

oldtel48 · Aug 9, 2020

pete12345 said:
Thanks very much for the assistance I think it will press out now that nut stays in place for the hub alignment there’s no need to remove it

Are you replacing the top and bottom ball joints
I have just done the offside ones on my motor got to do the near side this week what a job best of luck

pete12345 · Aug 9, 2020

Yer I’m doing both sides just waiting for rimmer bros to get some originals in stock

oldtel48 · Aug 9, 2020

pete12345 said:
Yer I’m doing both sides just waiting for rimmer bros to get some originals in stock

I have put britpart one’s in just hope that they are better than the 3maff sensors I had on warranty thank goodness

pete12345 · Aug 9, 2020

Not sure but on thing like ball joints that are a ball ache I guessed original so won’t ever have to do them again I hope

oldtel48 · Aug 9, 2020

pete12345 said:
Not sure but on thing like ball joints that are a ball ache I guessed original so won’t ever have to do them again I hope

I think I shall have to put a new axle on as I believe this is the third one’s,you can only put 3 sets in

frostythor · Aug 9, 2020

Rimmer are fine but Bearmach tend to give 3 years warranty on all there parts

pete12345 · Aug 9, 2020

Ok cheers will have a look but normally I use island 4x4 because there local to me

Datatek · Aug 9, 2020

pete12345 said:
Ok cheers will have a look but normally I use island 4x4 because there local to me

I bought mine from Island 4 x 4.

oldtel48 · Aug 9, 2020

Datatek said:
I bought mine from Island 4 x 4.

Tell me where they britpart

Datatek · Aug 9, 2020

oldtel48 said:
Tell me where they britpart

No

oldtel48 · Aug 9, 2020

Datatek said:
No

I do hope I have not done the wrong thing I better sell it after I have done them

Datatek · Aug 9, 2020

oldtel48 said:
I do hope I have not done the wrong thing I better sell it after I have done them

Britpart stuff is not all bad.

oldtel48 · Aug 9, 2020

Datatek said:
Britpart stuff is not all bad.

I must say I have had good value from britpart

pete12345 · Aug 9, 2020

I looked at island for originals but they didn’t have any

pete12345 · Aug 9, 2020

As data says all Britt part suff isn’t dodgy

tomcat59alan · Aug 9, 2020

pete12345 said:
As data says all Britt part suff isn’t dodgy[/QUOTE
Edit, isn't always dodgy.

oldtel48 · Aug 9, 2020

pete12345 said:
As data says all Britt part suff isn’t dodgy

I have had a lot of parts for britpart and been very satisfied with except for the maff sensors as I mentioned earlier which I must say they did reimburse with no trouble my supplier did it all for me

pete12345 · Aug 9, 2020

Some parts you can’t even get originals now you have to buy oem

P38A Ball joints

Well-Known Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Member

Well-Known Member

Well-Known Member

Well-Known Member

Member

Well-Known Member

Similar threads