Another idiots guide needed please

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Fit replacement high pressure jets and if needed the HP hose back to the washer bottle, at the rear of the washer you'll find the HP pump along with front and rear pumps.
It's all standard stuff. Simples.
I assume you have the existing factory fitted electrical side functioning correctly.
 
discool said:
Fit replacement high pressure jets and if needed the HP hose back to the washer bottle, at the rear of the washer you'll find the HP pump along with front and rear pumps.
It's all standard stuff. Simples.
I assume you have the existing factory fitted electrical side functioning correctly.
Click to expand...
The only bit that works is the front screen, rear screen is on a separate switch which is faulty...got one coming from eBay.

Wasn't sure if it was as simple as just connecting it to the washer bottle, cheers
 
Pootz said:
The only bit that works is the front screen, rear screen is on a separate switch which is faulty...got one coming from eBay.

Wasn't sure if it was as simple as just connecting it to the washer bottle, cheers
Click to expand...
It the HP hose is disconnected at the washer bottle and if the pump is working u would loose a bit of fluid, when the washers are remove the normal procedure would be just to plug the hose somewhere near to where near by, So have look might find the black HP hose plus the one way valve with its inlet and two outlets, the hose runs up and along the near side inner wing to the washer bottle.
 
Last edited:
discool said:
It the HP hose is disconnected at the washer bottle the if the pump is working u would loose a bit of fluid, when the washers are remove the normal procedure would be just to plug the hose somewhere near to where near by, So have look might find the black HP hose plus the one way valve with its inlet and two outlets, the hose runs up and along the near side inner wing to the washer bottle.
Click to expand...
Thanks. Going to be the weekend when I'm able to spend any time on it now as just found out my daughter's filming next week so I'm now playing roadie and logistics manager ( in other words, I'm driving and lugging the gear about)
Hopefully by that time the washer jets will have arrived from eBay
 
Pootz said:
I've got holes in my bumper that I was informed are for headlight washer jets...How do these wire up in simple term please or can I just run a pipe from the windscreen washer jets with a T piece.
I'd rather have them there instead of holes
Cheers
Click to expand...
The washer bottle, (engine bay lhs firewall), on it's rear side would have had one small pump for windscreen washers, and one large pump with 1/2" pipe discharge to service the headlamp washers, both the Discos I have owned had them, so if the pump is still there you will need the jets for the bar and a bit of nylex garden hose to hook them up, switch and wiring should still be ok, pump may have seized though if not used for a long time.
 
This is what I have. Are you saying they've been removed and you now have two holes?

maxresdefault.jpg
 
You must log in or register to reply here.

Similar threads

DollyBird
Engine disabled, keys not working, tried the guide “Re-synching the Range Rover P38 diesel engine with the Solved - BECM using a Nanocom” no luck
Replies
9
Views
2K
DollyBird
DollyBird
C
L322 Quick guide to servicing rear wiper washer
Replies
0
Views
4K
carldtrnr
C
D
K Series Guide/ Build Log
Replies
7
Views
3K
DanielG
D
Goc3k
Discovery 1 SOLD 1997 300TDI manual D1, Winchester
Replies
16
Views
4K
Goc3k
Goc3k
Bife
RAVE on Win10
2
Replies
33
Views
5K
Bife
Bife
Back
Top