Disco 2 Aftermarket Double Din stereo install

RyanDay1 · Dec 4, 2016

gstuart said:
i bought the D3 7 x seater base model , bought it as a project , so didn't want the immense extra electronics of the higher hse models

see some fit a standard sat nav , i.e. garmin, tom tom in where the sat nav normally is

but as mine is the base model its easy to replace it with a double din, as it's not tied in with gps, sat nav , on board
computers

Me fathers request to show off his old girl on LZ, misses it, will probably get another once i take him to a pay n play

twas a stunner

biggeeeee · Dec 4, 2016

Looks good so far , looking forward to see the end result

RyanDay1 · Dec 4, 2016

Cut and test fitted supporting plastic

Test fitting the lot with cage before securing it in, fitting and lining up nicely

Difficult to hold it all in line with one hand

RyanDay1 · Dec 4, 2016

Fixed the plastic to heater surround

RyanDay1 · Dec 4, 2016

Have roughly glued it in, this was the hardest bit so far one bit just didnt wanna stick but i shouldnt matter once its filled

Tried glueing this bit by just running a shoddy bead, will clean it later only to hold it there till i do something about those tabs
Time to fill it

RyanDay1 · Dec 4, 2016

Starting the fun that is filling, my skills are... Improvable

filling is the most fun though, messy! The starting bridging to build on

neilly · Dec 4, 2016

@RyanDay1 ,

Please ......................CLEAN THE BENCH!!!!!!!!!!!!.................... then carry on with the filling.

Cheers

brian47 · Dec 4, 2016

neilly said:
@RyanDay1 ,

Please ......................CLEAN THE BENCH!!!!!!!!!!!!.................... then carry on with the filling.

Cheers

'sAlright, it's not the bench, it's the kitchen table!

Grezzer · Dec 4, 2016

Love your enthusiasm, my patience would have burst with the first stage and it would have ended up all over the "KITCHEN" & table, hope it all works out well.
Now where's my garmin

RyanDay1 · Dec 4, 2016

neilly said:
@RyanDay1 ,

Please ......................CLEAN THE BENCH!!!!!!!!!!!!.................... then carry on with the filling.

Cheers

Dunno what youre on about you could eat off it

And me 'ands

Tillytomp · Dec 4, 2016

though you was meant to put filler on with a knife or blade, not your fingers

brian47 · Dec 4, 2016

RyanDay1 said:
Dunno what youre on about you could eat off it

See. I told you it was the kitchen table!

neilly · Dec 4, 2016

Nuffin wrong with eating off of it.......will add to the texture of the food.....Perfectly OK for that.

But if you are doing a detail modification job then it should be clean........LOL.........You do not want to get lumps in your plastic padding.

Cheers

RyanDay1 · Dec 4, 2016

Tillytomp said:
though you was meant to put filler on with a knife or blade, not your fingers

Im only using salmon paté as filler so its not too bad

started using a blade but was useless in the tight spaces was going everywhere and the paté is quite thick so quite difficult to work with

RyanDay1 · Dec 4, 2016

Think im gonna start sanding now see what the fillers like then probs carry on

RyanDay1 · Dec 4, 2016

Sanding has brought it up well, not looking bad at all! Only hit it with the dremel so far so very rough

tulipandthistle · Dec 4, 2016

What are you going to do with the metal bracket that holds the facia?

Looks great so far!

RyanDay1 · Dec 4, 2016

tulipandthistle said:
What are you going to do with the metal bracket that holds the facia?

Looks great so far!

Not sure what you mean matey

RyanDay1 · Dec 4, 2016

Satisfied that im finished sanding the thing, its as good as im ever gonna get it with what i have, really happy with it so far, not perfect but after some filler primer and a good load of paint itll be more than enough for me, especially with the unit in!
Ready for paint then, arriving tomorrow, might get a chance tomorrow eve to get it painted a bit

Heres it getting there with sanding, and modelled by @DiscoJK

All cleaned and tested again with cage and trim, the trim is as snug fitting as it could possibly get, which is great! but is about 1-2mm from being useless i think so good job there

Hope ya'll like the pics

tulipandthistle · Dec 4, 2016

RyanDay1 said:
Not sure what you mean matey

LoL there is a metal bracket just above your heater controls and below your radio which holds the bit you are making wit two screws under the radio that is fitted to body under the dash.

Mine is Facelift, so not sure if they all have them, but I think they do.

It looks brilliant though. I am tempted myself now!

Disco 2 Aftermarket Double Din stereo install

Well-Known Member

Retired - Living the dream

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Active Member

Well-Known Member

Well-Known Member

Active Member

Similar threads