Disco 2 ACE woes

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
B

Berk

Member
Posts
62
Location
Carmarthenshire
Right, because I'm a lunatic and masochist, I'm attempting to recommission ACE on my disco.

Got a good used rebuilt ACE block, working pump.

Fixed all the pipes and have no leaks, lots of flow in the header tank.

Buuut, as soon as I hit about 10mph, I get the red ACE light and the bings.

I'm currently too poor for a code reader (wifeys freelander needed tyres and wheel bearings, and a spring, and ABS sensor...)

So, anything obvious I might have missed?
 
If ACE was previously removed, I can't remember if you have to turn it off via diagnostics to avoid warning lights. Have you re-enabled it?
 
I'm sure I read that ACE doesn't store codes, just let's you know while it's currently crapping the bed.

I do fear the only solution is diagnostics.
 
Check the solenoids, what resistance?

All plugs OK

Try another pressure transducer.

Read codes
 
It's probably the fault which made the previous owner to disable it, unfortunately without a proper diagnostic tool it's a guessing game and can be expensive to replace parts just like that. As long as there is serious fluid activity in the tank at idle you can drive it without fear untill you find the fault cos the pump is on the safe side. All you can do with multimeter s to check the solenoids resistance

for troubleshooting purpose: the resistance of both DCVs(top of the valve block, DCV1-toward front; DCV2-toward rear)= 2.7 Ohm, pressure control solenoid(on the left side of block) = 5.7 Ohm.
 
I'll have to drop the ace block to measure, but at least that gives me something to go on.

Previous owner removed ACE for rotted pipes, have replaced all leaky pipes and the block and pump, so, hoping it's nothing much.
 
Worth a try, those values i posted were measured with high quality proffesional multimeter, there can be a certain difference between tools too, if we presume that your tool is reading 0.7 lower then you are within limits cos a roughly 5% difference is accepted by the system too
 
I did have an ECU failure on the drive relays, may be worth buying an Ebay special as a spare.
 
Right: Saved codes

Code: 
Fault 04-02
DCV 2 Current out of range

Fault 04-05
Electrical fault in DCV1 circuit (fault 29)

Fault 04-07
Electrical fault in DCV1 circuit (fault 31)

Fault 06-01
Hydraulic pressure too low

Readings with bridged relay:

DCV 1 Current: 000.00
DCV 2 Current: 000.00
PCV Current: 000.00

Pressure sensor (bar) 16.91
Residual Pressure (bar) 005.29
System pressure (bar) 007.10
Upper Lat accelerometer 000.03
Lower Lat accelerometer 000.11


So I'm thinking I'll hit everything with contact clean, and have bought another ACE ecu, because won't hurt to have on the shelf!
 
You must log in or register to reply here.

Similar threads

Tango91
  • Poll
Disco 2 Things I wish I knew when I took the body off (99 D2 TD5)
Replies
8
Views
3K
FlatbedPilot
FlatbedPilot
MrGorsky
P38A 4.6 V8 won't pull, sluggish, otherwise runs fine.
5 6 7
Replies
135
Views
11K
MrGorsky
MrGorsky
MaxSpec
Tinworm & Teenage Bodges
Replies
6
Views
1K
MaxSpec
MaxSpec
rustyrangie
New engine woes, please help..
2 3
Replies
55
Views
5K
classic kev
classic kev
dinisrosa
Defender td5 10P - no air pressure
2
Replies
38
Views
4K
dinisrosa
dinisrosa
Back
Top