ABS Ring/CV Joint

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
domino

domino

Well-Known Member
Posts
2,014
Location
Edinburgh
So, while having the rear brakes done, I was having a nosey round the front and I've noticed that one of the teeth in the NSF is worn which probably accounts for the pedal clicking I have. The boot on that CV is also split.

Is the ABS ring part of the CV or are they separate? Just thinking for when I get round to fixing them :)
 
domino said:
Sorry Wammers - no matter how many times I read that....I don't understand. Wotcha mean?
Click to expand...

CV (Constant velocity joint) Casing (The outer shell) Sweated (Interference fit part, heated up to expand it then put over the casing and allowed to cool so it shrinks and grips the outer shell.) :D:D:D
 
tomcat59alan said:
After my post re. checking a steamed plug and your sweated post I really think we should come up with a pedantic old fart's book explaining the often forgotten long lost mysteries of car repair. ;):D:D
Click to expand...

:hysterically_laughi:hysterically_laughi

Don't give away trade secrets Alan keep em guessing. You know what i am on about i know what you are on about that's all that is needed. :D:D
 
Apologies for the thread necrosis.

I'm going to be changing the wheel bearings in both fronts shortly and, while I'm at it, I'll get the long overdue cv gator replaced. Seeing as the whole kit from Island is £20 I'll just get that as it'll sort the abs problem too.

Is there anything else I should replace as par for the course doing these jobs? I know the requirements for a huge press to sort the bearings and that's already covered.

Just wanna know if there's anything else I should add to my cart with island.

The CV kit is Britpart - acceptable for this? What about the bearings? - they have britpart at almost half the price of the 'Timken' 'kits'. Would they be sufficient or should I stick with the more expensive part?

Thanks all :)
 
domino said:
Apologies for the thread necrosis.

I'm going to be changing the wheel bearings in both fronts shortly and, while I'm at it, I'll get the long overdue cv gator replaced. Seeing as the whole kit from Island is £20 I'll just get that as it'll sort the abs problem too.

Is there anything else I should replace as par for the course doing these jobs? I know the requirements for a huge press to sort the bearings and that's already covered.

Just wanna know if there's anything else I should add to my cart with island.

The CV kit is Britpart - acceptable for this? What about the bearings? - they have britpart at almost half the price of the 'Timken' 'kits'. Would they be sufficient or should I stick with the more expensive part?

Thanks all :)
Click to expand...

I've used the Britpart CV boot kits with no issues (so far). They're not as nice as the Land Rover ones (you'll see when you get it off, particularly the clip) but seem to do the job.

I'd advise against the Britpart oil seal for the half-shaft though. The Land Rover one used to be £12 but I couldn't see one at Island last time I looked. Maybe no-one was buying them.
 
Where are the bearings made? That will answer the question, imo.

Sweden, Germany etc.

I would not touch anything like this from the far east any more, but I guess if you don't use the car much it is not so important .....

Surely the oil seals are there? .... I changed mine not so long ago ...... GENUINE ones only (sorry to be so repetitive!).
 
Never done the bearings. Sorry. I'd go with Spiggy though. Bearing aren't that expensive and the spec from the east just isn't worth thinking about. Bugger of a job as it is so not worth skimping on.
 
SpiggyTopes said:
Where are the bearings made? That will answer the question, imo.

Sweden, Germany etc.

I would not touch anything like this from the far east any more, but I guess if you don't use the car much it is not so important .....

Surely the oil seals are there? .... I changed mine not so long ago ...... GENUINE ones only (sorry to be so repetitive!).
Click to expand...

That depends where the Germans and Swedes get their bearings made these days.:D:D:D
 
Yes, well, never assume anything!

Is nothing sacred! :)

Certainly you can get good quality alternator bearings .... at least that's what the seller says!
 
SpiggyTopes said:
Yes, well, never assume anything!

Is nothing sacred! :)

Certainly you can get good quality alternator bearings .... at least that's what the seller says!
Click to expand...

Places in the east are quite capable of making good bearings. Problem is that known name makers get them made there because it is cheaper. It's not the ones made in officially licensed factories to the correct specs that are the problem. It's the ones made in the factory across the road out of cheese and put in genuine boxes that cause the trouble.
 
You must log in or register to reply here.

Similar threads

A
FACELIFT Freelander 2005 outer front CV joint - specialized ?
2
Replies
25
Views
2K
Arnodafe72
A
N
Freelander 1 rear inner cv joint - mystery ring?
Replies
4
Views
1K
Nodge68
Nodge68
Brucey89
Drive shaft joint constant velocity boot split offside front Range Rover L322 2010 Vogue SE 4.4 TDV8
Replies
14
Views
3K
Anaconda
A
G
RR 55 plate l322 vogue
2
Replies
30
Views
1K
stuu
stuu
C
Front Drive Shaft CV/Gator boot
Replies
4
Views
980
htr
htr
Back
Top