4L Cyl Heads

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
R

range

New Member
Posts
49
Hi haven’t been around for a long time
I went out and got another Range Rover
This is a p39 on a N plate 4L with Head gaskets gone
Do they suffer with cracking the Heads?
I know they have liner problems
Every thing works but tatty
Michael
 
4.0 4.6 all do the same pours block goes hand in hand get the block rwlinered and ceramic sealered and it should be fine
 
jamesmartin said:
3.9 ,l4.2 ,4, 4.6 all the same cracking not porous,but what do you do bare relinered tophat block for
Click to expand...

Sorry you are wrong you can have a pours block and a cracked block
A cracked block will give you a slipped liner
A pours block will give you water pressurisation issues and loss and usage

Pours is more coman than a slipped linner
A pours block if caught early can be fixed with the irontite treatment but it is a 50/50 chance
 
ive removed alot of liners and only ever found cracks in ali bore but not saying its impossible depends on your experience
 
Experience 20+ engines a year and growing never had a failure. And I warrant the engine for 12k most don't so am happy with my quality of workman ship or engineer firms work
 
Well she is in bits
The Head gaskets are showing where they have been burning on both sides
No 2 pot
The liners don’t look as though they have dropped so will have the heads skimmed and see how bad they are then I can work out what I will do with her
But I am thinking of refurbishing the heads and all so putting some car go Seal up in as well
The water pump is all so shot
Any throats welcome
All so what is the best Head set for the 4L?
 
Thanks I all ways try to stay Genuine so it is good to know
Have you used Seal Up before and if so what do you think?
 
Any sealer is just a bodge!
Only sealer I would try is irontite
Yes contradictory but been down this route irontite is the only sealer I have used that does work unless it is a major failure of the block
 
No I don’t use them either just that it seams to be that there every where these days
So just asking
Haven’t played with V8’s for a long time manly Jags and Astons
Went mad on eBay and ended up with this started of at £600 ended up at £400 so it is just for fun really
Will put Gas on if she runs ok
 
Hi all and thanks again for your help
Didn’t get much time on it this week but sorted out the electric fans going to use Rover 400
The frame is designed to take 2 fans but only have one so I have put 2 in
The frame is just right and with the fixing brackets does the job grate
And have most of the Gas on as well but have to find some where to put the torpedo tanks
The engine is nearly finishes so hope to have it running this week end
If I get time
 
vougese39 said:
Sorry you are wrong you can have a pours block and a cracked block
A cracked block will give you a slipped liner
A pours block will give you water pressurisation issues and loss and usage

Pours is more coman than a slipped linner
A pours block if caught early can be fixed with the irontite treatment but it is a 50/50 chance
Click to expand...
how many blocks have you removed liners to prove pourous or cracked
 
loosing count average 3 engines a month buy another 3 a months for stock been stripping them since 1990's when was at land rover you?
 
on average every block as i have them tested before and after removing liners then retested after fitting usualy every 5 one needs the block welding
 
You must log in or register to reply here.

Similar threads

T
Electrical help!!
Replies
5
Views
1K
Nodge68
Nodge68
G
RR 55 plate l322 vogue
2
Replies
30
Views
1K
stuu
stuu
G
P38 4.0 v8 Automatic goes into low range all on its own
Replies
9
Views
1K
Datatek
Datatek
ar1g3
P38A Head gasket advice needed
2 3 4
Replies
76
Views
7K
Grrrrrr
Grrrrrr
marjon
L322 Key fob case replacement.
Replies
5
Views
526
marjon
marjon
Back
Top