robint
Well-Known Member
- Posts
- 7,057
300TDi Squeeling belt 'Penny Trick'
- Thread starter battenberg
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Not sure he got it from paddocks
robint
Well-Known Member
- Posts
- 7,057
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
no not yet ,but id allways use a genuine one from bp or bearmach
I'll see that he orders a real one next time
Basil5279
New Member
- Posts
- 12
- Location
- Co. Waterford, ireland
Daft question, but is the tensioner on the right way round?
If you haven't done one before, the printed instructions I had with a dayco kit a few years back weren't clear. I put the new one on the same way the old one came off-1000 miles later I was replacing pushrods and the timing belt kit again.
Embarrassing but luckily no major damage. Also discovered the PO had shifted the fuel pump timing by 1 tooth of the belt. :-(
If you haven't done one before, the printed instructions I had with a dayco kit a few years back weren't clear. I put the new one on the same way the old one came off-1000 miles later I was replacing pushrods and the timing belt kit again.
Embarrassing but luckily no major damage. Also discovered the PO had shifted the fuel pump timing by 1 tooth of the belt. :-(
deffo right way round
he gave it a spin when he took it off and it makes a racket, just crap quality.
yes it was britpart, i dunt think he'll do that again
keithrturner
New Member
- Posts
- 8
- Location
- Kidderminster
Changed my alternator last week and it started squeeling after. Cleaned all belts as I thought it couldd be crap in the grooves but no joy, oiled all bearings and moving bits, still no joy. Did the penny trick - BINGO!
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
scouse6744
New Member
- Posts
- 1
thank you......worked a treat :fighting2:
- Posts
- 58,170
- Location
- Preston Lancs.
Squeal is caused when bearing goes out of line because plastic sleeve the tensioner revolves on wears at one side. If you take tensioner off, strip it, and turn sleeve round all is good again.
Hi
I replaced my bearing yesterday, the bearing had a lot of play and made the tweety bird noise till about 2,500k revs then changed to a grondy sort of noise. The issue i now have is the new bearing is constantly squeeling and there is still a bit of play, could the old bearing of damaged the centre shaft?
Thanks
I replaced my bearing yesterday, the bearing had a lot of play and made the tweety bird noise till about 2,500k revs then changed to a grondy sort of noise. The issue i now have is the new bearing is constantly squeeling and there is still a bit of play, could the old bearing of damaged the centre shaft?
Thanks
Hi guys,
Just wanted to say a big THANKYOU for this thread!
I have just completed the 'Penny Trick' on 'Nelly' my Defender who was squealing like a banshee.... and there's no more squeal!
I am well chuffed!
Proud of my skills with a spanner and a penny!
Cheers everyone!
Just wanted to say a big THANKYOU for this thread!
I have just completed the 'Penny Trick' on 'Nelly' my Defender who was squealing like a banshee.... and there's no more squeal!
I am well chuffed!
Proud of my skills with a spanner and a penny!
Cheers everyone!
freddybulmer
New Member
- Posts
- 6
- Location
- York
just to put my 2 pence in on this one...
I have a 1996 300tdi which was recently re-built. No noise from the belt before it was re-built (although at that point the rest of the car was knackered!) but since its been back on the road the noise from the belt is driving me mad!!
It is every time i start the engine. when i dip the clutch, the noise stops but only until I lift the clutch again! It gets louder as the revs go up when accelerating and then when the engine gets to the correct temperature the squeeking seems to stop...
Does this sound pretty standard for a 300tdi and like the penny thing will fix it??
Cheers folks
I have a 1996 300tdi which was recently re-built. No noise from the belt before it was re-built (although at that point the rest of the car was knackered!) but since its been back on the road the noise from the belt is driving me mad!!
It is every time i start the engine. when i dip the clutch, the noise stops but only until I lift the clutch again! It gets louder as the revs go up when accelerating and then when the engine gets to the correct temperature the squeeking seems to stop...
Does this sound pretty standard for a 300tdi and like the penny thing will fix it??
Cheers folks
battenberg
Well-Known Member
- Posts
- 2,101
- Location
- Birmingham UK
It'll cost u a penny to find out
gemsdad
NOT BOTHERED.
- Posts
- 67,807
- Location
- halfway between here and there.
you sure it aint the thrust bearing??
