- Posts
- 22,902
- Location
- In the next Glen
rum n coke
i lifted my l@ptop @ my rum n coke but hit the t@ble l@mp with the gl@ss = g@me over 
300 tdi won't rev over 2000
- Thread starter jack.parker
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
rum n coke
i lifted my l@ptop @ my rum n coke but hit the t@ble l@mp with the gl@ss = g@me over jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
When it is running at 1800,,pouring out smoke,I can remove intercooler hose and it makes no difference.
tottot
Well-Known Member
- Posts
- 8,028
- Location
- west wales coast
Remove pipe to turbo inlet and try. [ be sure nothing about to suck into turbo.]
GRATCH
HUGE MEMBER
- Posts
- 15,475
- Location
- North Cheshire
After you've removed inlet pipe on turbo and before you start engine, see if you can spin the turbo vanes round with a finger.
That is a pump or timing issue.
Nice to see one that has not had windows cut into the sides.
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
The cam belt was changed by a garage a week ago, no black dust visible and the fuel supply trick,I will try that at the weekend.
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
Bet it’s a tooth out…
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
I have done that, and i actually thought at the time that the turbo should have been a lot easier to spin. That is why i took the pipe off last night again and it was spinning well on tick over.
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
But it has been running fine since the belt change, unless it has jumped a tooth. I have only driven it 12 miles since the belt change.
Hicap phill
Well-Known Member
- Posts
- 16,238
- Location
- Wiltshire
So have you been able to go faster than this ?
I see you have changed a lot of bits.
If you hold the pedal down does it die at all or just reach max restricited revs?
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
It just hits a wall when you rev it up, even when you do it slowly.Then if you give it more throttle the smoke starts..I noticed when i have been driving and i change down, the revs obviously rise, but the engine is just like a petrol when you turn the ignition off when driving,,,,,,,,,,,,no response.
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
just hits approx 1800 and no more, pressing the pedal further produces smoke
- Posts
- 4,549
Could it be a collapse of the turbo outlet pipe ?
My 300tdi had a similar (although not as severe) problem that was caused by the flexible turbo outlet pipe that had delaminated causing a constriction ....
Although i'm not leaning in this direction (it does sound more of an 'air problem'), another issue could be the FiP.
You can get it checked by Ribble Valley (Diesel Bob) for around £110
If you feel up to it i'm near Lanark and would be happy to have a look around the engine if you can get oit here ...
My 300tdi had a similar (although not as severe) problem that was caused by the flexible turbo outlet pipe that had delaminated causing a constriction ....
Although i'm not leaning in this direction (it does sound more of an 'air problem'), another issue could be the FiP.
You can get it checked by Ribble Valley (Diesel Bob) for around £110
If you feel up to it i'm near Lanark and would be happy to have a look around the engine if you can get oit here ...
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
Could never get near Lanark, I have a friend George in Falkirk (expert) he is thinking about it...I am getting a compression test done next week.
I reckon 16yrs standing aint done that ip any good
On my 200 it would run on three whilst chucking out white smoke like a battle ship of old, then after 5 miles or so would chime in on all four running fine until next cold start, another pump sorted it, tried all sorts injectors/cleaners/filters/hoses etc etc.
+1.
OP, Are the garage who did the job a LR specialist ? - it's quite easy to check the timing of the FIP through the inspection cover in the tc cover.. worth doing IMO. Even checking
the cam timing isn't a mare of a job ..jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
Ran a separate fuel supply to Injection pump today......no change. Took off the blanking plate at EGR, and ran the engine.....no change
jack.parker
Member
- Posts
- 21
- Location
- Kirkcowan
+1.
OP, Are the garage who did the job a LR specialist ? - it's quite easy to check the timing of the FIP through the inspection cover in the tc cover.. worth doing IMO. Even checking
IMO ??
Flossie
Well-Known Member
- Posts
- 11,001
- Location
- Shropshire
In my opinion.
