200tdi ran with no oil

ozzyboydeano · Nov 10, 2018

robal said:
Right well the sump had coppery glitter in it. And the oil pumps mesh had copper glitter and crud on it...

normally when an engine runs out of oil for a period of time the bottom end is removed first not the lid (head) for inspection of damage

spun or damaged big end bearing / main bearing as well as thrust washer damage ?

hopefully your specialist does some measurements of his own before installing new bearing shells

Blackburn · Nov 10, 2018

Are the bronze bits the cam shaft bearings , thrust washers are copper coated one side if I recall but would not think that thickness.
Edit late thought cam followers are brass!

robal · Dec 10, 2018

Hi chaps,

so having taken the engine in, they have reground the crank and also the bores so i'm looking forward to getting it back this week and slinging it back in the truck. I'll keep you updated with whats what!

robal · Dec 12, 2018

Ok. So how hard is it to set the timing belt. The chaps at the garage are offering to a) give me the block back with pistons in b) block back with timing cover on and belt set....

Thw difference is a 180 pound. I reckon it cant be that hard. What do you think??

Disco1BFG · Dec 12, 2018

The cynic in me might suspect they are nervous of something, and are covering their behinds ...

It is NOT difficult at all to fit the timing belt.... But don't take my word for it ... have a nosy here:-

http://www.glencoyne.co.uk/belt.htm

robal · Dec 12, 2018

Disco1BFG said:
The cynic in me might suspect they are nervous of something, and are covering their behinds ...

It is NOT difficult at all to fit the timing belt.... But don't take my word for it ... have a nosy here:-

http://www.glencoyne.co.uk/belt.htm

I took it to them with the timing cover on as i couldnt get the pully off and might think im a bit of a mug (to be fair i am)

thanks for that. I've always found glencoyne pretty handy! Do you think i need to replace the seal in the bell housing?? It went on only a few thousand miles ago most. plus, the head and head gasket didnt blow, do i need to get that re skimmed or not?

Disco1BFG · Dec 12, 2018

I think I'd replace the seal due the lack of oil situation. Crank pulley tool is only about 30 odd £.....

If you're confident in the head, then pressure testing would be my choice .... I'd only skim the head if you have to ... can only be done so many times and 200 heads are no longer made .... which means a second hand replacement with unknown provenance ..

Unless you really want originality, or you are too far in financially, I'd maybe consider replacing the whole engine - cheaper and quicker... a shame, but life deals some rubbish cards at times

robal · Jan 10, 2019

right, so the head is back and all ok and the block is on the stand and all the new parts are laid out......
I have 2 questions though!

1) the chaps who ground the crank etc supplied me with all the bearings for the bottom end, they are all larger sizes than the original apart from the thrust washers, these are standard which sort of makes sense but i don't have a dail test indicator, can i just use feeler gauges to measure the end float??? do i have to??
2) tightening the head back on - i have used the sealey/clarke torque dial angle measures before, they are really crap and i've never been confident with them. does anyone know anywhere to rent a digital gauge or a good quality angle dial?

jamesmartin · Jan 10, 2019

robal said:
right, so the head is back and all ok and the block is on the stand and all the new parts are laid out......
I have 2 questions though!

1) the chaps who ground the crank etc supplied me with all the bearings for the bottom end, they are all larger sizes than the original apart from the thrust washers, these are standard which sort of makes sense but i don't have a dail test indicator, can i just use feeler gauges to measure the end float??? do i have to??
2) tightening the head back on - i have used the sealey/clarke torque dial angle measures before, they are really crap and i've never been confident with them. does anyone know anywhere to rent a digital gauge or a good quality angle dial?

you can feel it when it comes to end float or use feelers ,there has to be some,but a few extra thou wont hurt
for the 60 degrees mark a bolt flat corner and the head and turn it one flat for the 20 degrees guess a 3rd of a flat mark the top of each bolt as you go and on each sequence

200tdi ran with no oil

ozzyboydeano

Well-Known Member

Blackburn

Well-Known Member

robal

Member

robal

Member

Disco1BFG

Well-Known Member

robal

Member

Disco1BFG

Well-Known Member

robal

Member

jamesmartin

Well-Known Member

Similar threads