- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Let me check the part number on it. It might be the 2238. I'll have a dig around later.
1996 RR 4.0 SE hard to stop, pump keeps running
- Thread starter Rover9676
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Let me check the part number on it. It might be the 2238. I'll have a dig around later.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Right, I've had a dig around and in fact I have an ANR2238 and an ANR2239.
However, I am not sure it will help you as there must be a reason I replaced it! One of them I know for a fact I had apart and it wasn't designed to be pulled apart. Would it work or indeed be safe? I just don't know and I'm not sure I'd feel comfortable gambling someone else's life on it. I'm pretty sure I had the ANR2239 apart as that's the one I also have on the car. The ANR2238 I kept in case I ever wanted to return the car to original spec.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 4,653
- Location
- Rotherham
Hi Rover9676 just returned from holiday (vacation to you) glad to see wammers has been on and sorted you out. He is the best. I had an ABS fault a while back and he helped me too. Anything I can learn from him I try and pass on to others. Hope you are back on the road again soon
Wammers is great! In fact you, grrr and others were as well. Much appreciated! Now I have to try and source an affordable ANR2239 Master cylinder unit. Keel your fingers crossed!!Hi Rover9676 just returned from holiday (vacation to you) glad to see wammers has been on and sorted you out. He is the best. I had an ABS fault a while back and he helped me too. Anything I can learn from him I try and pass on to others. Hope you are back on the road again soon
Thanks you for looking. Will continue the search.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
Loads on ebay over here. If they won't post overseas I am sure one of us can take delivery and forward it on. Sometimes one of us ventures across the pond. @Wazzajnr for one, I think.
If you inquire how much it costs and it affordable after I add-in shipping cost, it may work.
Thanks,
Hey all, yesterday I found a master brake unit on Ebay in the UK. It should arrive between November 7-12. I will keep you all posted.
- Posts
- 4,653
- Location
- Rotherham
Well done looking forward to hearing good news at the end of this
Okay everyone, today I received my master cylinder for my 1996 Range Rover 4.0 SE Automatic. Please chime-in with any do's or don'ts, needs to know, pit falls to avoid and helpful hints. I didn't know whether to clean it or not. That may cause problems. I hope to get to the swap this weekend.
Thanks
Not got any USA trips planned for a while and I suspect it would be prohibitively expensive taking that in a suitcase.
Shipping to the states isn't expensive if you're not in a rush.
- Posts
- 19,297
- Location
- Buckinghamshire, UK. ('95 DT)
I'd clean it. I think there are videos on YouTube. I need to clean mine. In order to see the fluid level you have to shine a Maglite through the filler on mine!
I don't remember any issues swapping it over. The brake light switch may need resetting afterwards - pull the plunger out, refit and then press the pedal a few times and it'll find its level.
Flushing all the air out of the modulator is the ball-ache. That's where a means of pushing the fluid through comes in handy. Don't skimp on time at that point. Lots of rags to make sure no fluid gets near the paint.
Good morning all, I cleaned my reservoir with Simple Green (A biodegradable degreaser). Filled reservoir, shook it, let it soak for ab 1.5 hours turning it upside down for 40 minutes than right up fir awhile. It did a fairly good job but I did notice some residual when it dried. In the filler chamber I got it all out but, in that separate smaller chamber at the top didn't rinse totally clean. I bolted the unit back up but wondered if it okay or should I try cleaning it again before filling it with brake fluid and connecting the pipes, lines and hoses. Do you all think it's okay or should I pry off the reservoir and try again?
Thanks
What type of solvent?
isopropyl alcohol used to remove brake fluid traces from hydraulic braking systems, so that the brake fluid (usually DOT 3, DOT 4, or mineral oil)
Hey there, some of your writing was left off. Would you finish your remark.
Thanks
