markinofficeuk
Member
- Posts
- 11
Series 3 109 Front Right Inner Hub Seal 1981
- Thread starter markinofficeuk
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
RTC3528, £1.98 inc VAT as advertised on Paddock's web site? Personally you'd be better going for the whole overhaul kit at £21 or so as also advertised given you have to dismantle the hub anyway. Treat yourself to hub gaiters whilst doing so?
There is a way of changing it without pulling the hub apart. If you remove the spring from the new seal and un-thread it from itself to open it out, cut the rubber seal with a sharp knife and then cut the metal ring with a hack saw to complete the cut you can then open the ring and thread it round the axle tube (yes it will go, just. Best buy two replacements just incase though). Once over the axle thread the spring back into itself and locate it in it's original position, then install the lot into the swivel hub with the slit in the rubber at 12 o'clock. Put a smear of hylomar blue over the slit in the rubber for added peace of mind.
I did the drivers side on mine that way 4 years ago and the passenger side a year ago, both are fine.
I did the drivers side on mine that way 4 years ago and the passenger side a year ago, both are fine.
markinofficeuk
Member
- Posts
- 11
That's great John. Thank you so much.
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
Isn't it the inner hub seal you require and not the swivel seal?
markinofficeuk
Member
- Posts
- 11
Yes, it's the Inner Hub Seal. As you can tell I'm not a mechanic. Do you have a part number for this seal? Thanks
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
I've got a parts catalogue here. What year / model and engine is yours 88" or 109"
markinofficeuk
Member
- Posts
- 11
Hi, it's a 1981 series 3 stationwagon 109 front right inner hub seal. Thanks again.
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
Just seen your model and year. Your part number is RTC 3511 this is for models like yours after October 1980
markinofficeuk
Member
- Posts
- 11
Thank you for your time. I really appreciate it. Mark
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
No problem. Try and source a good make like Corteco if you can. Never had any trouble with mine since I replaced them.
Land Raver
Well-Known Member
- Posts
- 2,015
- Location
- In the dog house
Here is a link. The genuine will probably be made by Corteco. The cheapest wil probably be Britpart and best avoided!
http://www.lrseries.com/shop/product/listing/10653/RTC3511-HUB-OIL-SEAL.html
http://www.lrseries.com/shop/product/listing/10653/RTC3511-HUB-OIL-SEAL.html
Bit confused by the photo - is it the seal that runs on the swivel ball you need? to help you identify it here's a link to the parts book. http://www.landroverweb.com/landrover/pdf-land-rover-manuals/ If it's the swivel seal there's a better cheat that doesn't involve cutting the seal. Remove the brake pipe and steering link, undo the six bolts holding the swivel ball to the axle and pull out the hub, swivel and driveshaft in one lump. The hub seal will fit over the axle end of the swivel.
RobertP
Active Member
- Posts
- 320
When I replaced my front seals a few years ago I had a devil of a job getting the half shafts back in, especially the longer one. The inner ends droop, so I couldn't get them into the diff. I got round it in the end, but is there an easy way?
