Search results

The first electric pump I fitted was a cheap one, like a square Facet, but not... It leaked within a few weeks of fitting. The Facets aren't that much dearer (unless things have changed) and IMO are worth the extra.

It does have a filler bung on the side, you fill it via that and then that same reserve is kept topped up by splash. Nothing to stop you checking level through the filler bung if you want to. The overdrive holds half a litre and there is a drain plug fitted as well.

As the bishop said to the actress...

They are an easy fit, just follow the destructions to the letter. One thing: I'm not sure if this is mentioned in the destructions but in case it isn't: there is a little steel band/ring over the gearchange nubbin on the back of the unit. Whatever you do, leave that (wired on?) ring on until the...

Mine's a 109 FFR and the pipes go into the chassis.

Just wondering if a piston hit an inlet valve and bent it very slightly. Happened to me when the timing belt gave out prematurely on my old Fiesta diesel. I wouldn't have noticed except the valve wouldn't grind in properly only touching down on the seat half way round. You couldn't see any...

Col So what you have is a military tank with under-seat filler cap? Last time I had to clean a tank in-situ I flushed it with water using a power washer and used a wet/dry vacuum cleaner to get most of the wet out, there were no fumes to worry about, the hot air blower soon took care of any...

Had this same problem a few times over many years. My first thought was an in-line filter with transparent body and paper element as has already been suggested, change the filter as often as necessary... Having said that, it seem you have quite a big contamination problem on your hands and I...

We used to grind them down to size with the bench grinder if the need arose. They are only made from carbon.

Petrols don't need or have a vacuum reservoir, the vac pipe goes direct to the inlet manifold just below the carb. 2.25 diesels have the vac pipe to the far end of the inlet manifold just behind a butterfly valve which is closed when the engine is idling, this causes vacuum in the manifold. When...

I fitted a new servo to mine a few years ago, (Britpart) the improvement to braking was significant but when I did the test I couldn't detect any pedal drop at all. However, the better braking was undeniable. I reckon Rob is right, an upgrade to a bigger servo is the way to go if you can afford...

So many have been scrapped, being considered worthless, that the remaining ones can only go up in value. I have an engine like yours from my 109 FFR which now has a 200 lump in it. Now that there is so much hostility towards diesels there has been a 180 degree turn in opinion of the petrol...

Each pair is one left-hand and one right-hand.

I used ordinary garden hose as trunking and fed through it, the correct coloured wires which I got from Autosparks. The hose, I fed over the transverse floor supports where they jump over (under) the longitudinal floor supports, it is out of the way and looks neat, you can push it though a...

Quite right, diagnose first and replace only that which needs to be replaced. A compression check is what I'd do first as well, make sure of the basic soundness of the engine otherwise all your efforts with ignition and carb might be wasted. You can buy a compression tester kit on Amazon for...

Firing order is 1,3,4,2. Distributor rotates anti-clockwise so if you look at Marmaduke's picture you will see that his is wired up correctly. If the distributor has been fitted correctly, the number one tower on the distributor cap should be the one nearest to number one cylinder as Marmaduke's is.

We have to acknowledge that the engine was turning over before, I can't see that the bores are too rusty and pistons seized... this is a strange one. Tottot's suggestion above is intriguing and worth thinking about. If it were mine I would be taking the head off and seeing what there is to see...

I've just replaced my Hi-Lo lever gaiter; it was a Britpart bit and it lasted about 4 years. I had greased it inside with ordinary yellow grease and sprayed the outside with silicone lubricant, idea being to keep the oxygen away. This time I used silicone grease on the inside of the new Britpart...

Interesting use of an extra pair of headlights, the ones in the grille are Marschal if I'm not mistaken?

This is my fitment, I made strengthening plates with 2mm steel, they are now boxed in and I'm back to standard LR seats.