Search results

I changed the head gaskets (V8 4,0 Thor) and in the process had to smash off the exhaust heat shields. As I didn't want to remortgage rather than get new ones I wrapped the manifolds which has been fine. She runs really nicely and has no codes. Today when doing a few bits I noticed a bit of...

I replaced the head gaskets on my p38 4.0 Thor a few weeks back and everything was fine. A few days ago notice a coolant leak from one of the hoses, tightened the clamp and pressure tested at 14 psi it to make sure it was ok I started her up and thought I heard a ‘whoosh’ noise from the engine...

Some advice would be appreciated please. Am in the process of doing the head gaskets on P38 4.0 Thor. The dipstick tube snapped pretty much level with the block when I tried to remove it. It is stuck in there solid. Someone mentioned a left hand drill bit would get it out. I tried this...

Hi Guys, A bit of advice needed please. I am in process of removing heads on 4.0 Thor. I am hoping to leave the manifold on for removal. Is it possible to get to the lower rear bolt on the passenger (LH) side with a normal socket? I am not sure if it is going on straight or at a slight angle...

Hi, I have a P38 2002 4.0 Thor. After 165k miles I think the head gasket has developed a small oil leak near the front on the drivers side. Very minor at moment and no issues at all and she runs perfectly. However I assume at this mileage it is only a matter of time before head gaskets need...

Hi. Have been an idiot and need some advice please. I removed the rear washer jet to unblock it and left a good inch or two of pipe hanging through the hole, no problem I thought. But when I went back the pipe had recessed back into the metal panel although I could just about see it. In trying...

Hi, I've searched the forums for this question but can't find an answer anywhere. Hopefully the vast knowledge of the forum can help. The CC on my 4.0 2002 P38 doesn't work. I have tracked the issue down to the BECM wheel / road speed output on pin 20 which goes to the CC ECU. I believe it...

Hi Guys, The headlining in my 2002 P38 4.0 is knackered. I am about to pull it out and recover and I am pretty sure it is one piece. I have seen this used 2 piece one advertised on eBay at island4x4 ...

Hi, My lovely girl -2001 4.0 P38 just sailed through the MOT at a mere 160k. However we had one advisory that I knew was coming on the offside front lower control arm balljoint. Having a quick look on the internet pressing kits to remove/install the ball joints made specifically to the P38...

Hi Guys, In the process of changing the valley pan gasket on my 2002 4.0. I'm about to start putting everything back together and RAVE indicated only to use a bit of RTV on the seals. I have however seen people mention using RTV or Blue Hylomar on the actual gasket, around the waterways and...

Hi, Not sure how but when I removed the oil filler tube whilst changing valve cover gasket the plastic thread is damaged and won't screw back in. Engine is a V8 Thor. My question is do I actually need the tube as they seem expensive for very little benefit, or is there an oil cap that will...

Hi, I had to change the oil cooler pipe on my v8 4.0 2002 from the front cover to the oil cooler. In the process of disconnecting from the oil cooler it stripped the aluminium thread on the cooler, which I now have learned is pretty normal. I ordered a new cooler (ESR 3204) suitable for all v8...

Hi Guys, Can anyone help? I was changing the front cover gasket on V8 4.0 Thor. When disconnecting the pig tail from the oil pressure switch I managed to ping the little metal 'clip' securing the connector across the drive never to be found again. I have searched high and low on the internet...

Hi Guys, i am in the process of changing the front timing cover on my 2002 V8 Thor. Starting to put everything back together. Now I know this is a numpty question but can’t for the life of me work out how the cam sensor bracket holds the cam sensor onto the cover. Have googled but can’t find...

Hi Guys, I have a 2002 P8 4.0. The air con has sprung a leak in the pipe as it runs along the firewall at the back of the engine bay before going down into dash and the evaporator. I can hear it hissing out and think it is the low pressure pipe. It looks like a mother of a job to replace the...

Hi, A bit of advice would be much appreciated. My air con on 2002 P38 hasn't worked for a few years but as it has generally been a "working" vehicle ( and fantastic ) it wasn't a priority. Over the last year I have spent many enjoyable hours getting her back to her former glory. The last bit of...

Hi. I would like to pick the brains of the P38 experts please :) After sorting out my heater matrix o-rings and putting everything back together the driver's side heating isn't working. Quick scan gave the fault codes in the attached pic. Before diving in I wondered if anyone had any thoughts...

So today I decided to replace the o-rings on the heater matrix as footwell damp. Used the 'quick' method of cutting hole for access and all went well. Old o-rings didn't look too bad to my surprise and I couldn't see obvious evidence of a leak but changed them over to the new ones. When I...

Hi, I've searched forums, internet and Rave to the best of my ability and can't find anything so am hoping the wisdom of the forum can help. I am replacing both my damaged wing mirrors ( the whole assembly not just the glass ) and as I couldn't find any in the right colour have got a couple of...

Hi. I have a 2002 P38 4.0. My other half unfortunately met someone going round the corner in the middle of the road on a country lane and need a new wing mirror. I have scoured the internet and local breakers for a replacement but can't find one in the right colour which is 507 Caledonian...