Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. xDParis64

    Freelander 1 Preserving the scarce ! FL1

    Not sure if this one has been posted, but quite a rare model and very low milage...
  2. xDParis64

    ignore thread please

    Oh, Didn't notice, was ignoring... Anyway, back to ignoring.
  3. xDParis64

    Unable to bleed brakes

    Anyone got any thoughts on this? I didn't remove the master cylinder to a point where brake fluid comes out, but maybe with the moving it around I need to bleed the master again?
  4. xDParis64

    Unable to bleed brakes

    Welp. I replaced the brake booster and it's worse... Now the first 7/8th of the pedal has no resistance and it won't build pressure, I tried to adjust what looks like an adjuster screw in the brake booster but it has not worked, when the engine is off the brake pedal becomes noticeably better...
  5. xDParis64

    Drinking Coolant / Head Gasket

    So didn't get a chance to look at the water pump, however, Managed to plug in my Pscan to log the current O2 sensor. As explained to me by @pscan.eu the O2 sensor should fluctuate between 0.2V and 0.9V Where 0.44V is a missing / wiring fault and 0.2/0.9 is lean and rich I logged the data and...
  6. xDParis64

    ignore thread please

    Sorry! Someone linked this thread, will ignore now.
  7. xDParis64

    Advice on new engine for Freelander 1 petrol convertible

    Here are the facts. I have tracks all expenses I have made on this car (excluding Fuel, Insurance and Road Tax) on just repairs and making it ready for green-laning. feel free to guess how much but It just below anyway. I replaced / repaired. Head gasket Engine Gearbox Skid Plate Various...
  8. xDParis64

    Drinking Coolant / Head Gasket

    I will keep an eye out! That will show up in the oil right? Maybe about time I do an oil change actually 🤔
  9. xDParis64

    Advice on new engine for Freelander 1 petrol convertible

    Honestly, same goal over here, more for green-laning than "off roading" the freelander would not handle it, but if you're up to the task chuck in the same engine, you could probably get an early pre-2001 engine for cheaper, I've got a guide on how to switch the 1.8 between the 2 versions (Wasted...
  10. xDParis64

    Drinking Coolant / Head Gasket

    Just a quick update on this one, I don't think (fingers crossed) it is still losing coolant, however, I think in the time it was, it has inadvertently fried the O2 Sensor? Would that be possible with enough Coolant going through the exhaust? (On this model I have only the 1 O2 sensor on the...
  11. xDParis64

    Freelander 1 Brake Line Sizes (Fixings Thread Size) SOLVED

    Dual seat SS lines seem great and are not leaking at all, haven't tested how they feel but we will see, closing this out as solved Fittings on a non ABS model are M10x1.0 on ALL fixings
  12. xDParis64

    Unable to bleed brakes

    Thank you! When pressing on the brake when I am under the dash in the pedal area, I can hear a hissing and it looks like the brown part under the rubber boot is very cracked my pictures are terrible but here you are:
  13. xDParis64

    Unable to bleed brakes

    Upon trying to drive this thing the brakes were still really bad, however I did have a hard pedal after pressing on it a few times when the engine was off, but when driving the pedal would lose the brakes until much lower in the pedal... I found a comment from @Nodge68 a while ago (Cannot find...
  14. xDParis64

    Unable to bleed brakes

    I appreciate the comments @pscan.eu and @Alibro I will be keeping this in mind for the future for sure, however, I was already planning to use custom brake lines for this vehicle (it is not a daily driver or even remotely close to such) so the difference wasn't the biggest deal and plenty...
  15. xDParis64

    ignore thread please

    Wait! Ignore? My bad! Just read the whole thread so far... will ignore from now on!
  16. xDParis64

    Freelander 1 Andyfreelandy's get together, North Devon, September 13th

    I'll probably be down during the day Saturday, but wouldn't be staying overnight, would be great to meet everyone though!
  17. xDParis64

    Freelander 1 Brake Line Sizes (Fixings Thread Size) SOLVED

    Couldn't agree more, would match the Blue Coolant lines too!!
  18. xDParis64

    Freelander 1 Brake Line Sizes (Fixings Thread Size) SOLVED

    Yeah, definitely my plan, it seems that the one I have found does 3 sets of flares, SAE, DIN and DUAL which is apparently a flare that can work with both almost "universally" I will be sure to ask them about it and report back. Will also update my other thread when the new lines come, just a...
  19. xDParis64

    Freelander 1 Brake Line Sizes (Fixings Thread Size) SOLVED

    That is exactly what I was looking for! Hiw couldn't I find this :rolleyes: None the less as mine is less ABS i should imagine they'll all be m10x1 they all seem to be the same size. Follow up though, I'm looking for custom SS braided lines, I assume they will still need the same flare ends or...
  20. xDParis64

    Freelander 1 Brake Line Sizes (Fixings Thread Size) SOLVED

    Hey all! This is a mini-post in relation to: https://www.landyzone.co.uk/land-rover/unable-to-bleed-brakes.398398/ : But I believe it would serve better for future looking if this was on it's own. I am looking to get some custom Brake lines for the Freelander but I was wondering if anyone...
Back
Top