Search results

Hello members, Is this a voltage regulator for dash instruments? Series 2a https://picasaweb.google.com/m/photo?uname=108034514694382291794&id=5816441758340092690&aid=5816442688970108657&start=0

Just bought a 15/16 spanner, thanks JamesMartin.

Anybody know what size the locknut is on the side of the steering box (for adjusting steering play)? I know its not metric, I'm not near mine. Series 2a. Thanks in advance.

Ok so LRA602, or perhaps A127 from a mini? I just want it to fit onto the series 3 bracket, . Thanks for your advice. I wish I knew of a wrecking/salvage yard full of British vehicles, I would be in heaven!

I need advice on upgrading my 17ACR alt. I would like a Alt with 60 amps or more output. I have AC installed plus a stereo and amp mounted inside a subwoofer box. The 35 Amp 17ACR isnt keeping the battery topped up. Anybody know what I need. I have searched for 20acr but not sure if it will...

I think your referring to the weather strip, hehe I think its supposed be there but not real sure, its working its way out. Thanks for the pic, I see your window lock just barley makes it flush, so I will just improvise a little maybe put a plastic spacer in between :-)

Got a couple of locks, and ran into a small problem. The locks do not get flush with any of the door frames for pop riveting. Not sure as to why the window channel hangs out so far, anybody have any suggestions or might know what the problem is. The windows are all tight. I am guessing the...

Thanks for the reply, I think the wrong specs got sent to the factory in wherever the last production run was. Anyways, I order another set this time from ebay. In the picture you can barley see the seals have a recessed groove in them. Should arrive in a couple of weeks, and I will update...

Are you sure its the starter? I thought I had the same problem 2 weeks ago, a loud high pitch shrill especially on revving. Turns out a washer from a bracket was rubbing on the alternator impeller fan. Just a thought.

part number - 330621 Anybody have problem when replacing your vent seals? I tried every which way. The seal is too thick, and the bottom of the vent does not come close to closing even when using a impressive amount of force to try and force close it. Anybody know if the vent seal is supposed...

Ok, solved! Newton or Murphy was right on. I crawled under the truck for 20 minutes and turned the slave so the bleeder is at the top. A lot easier then I thought it was going to be, and the when I pulled the slave out no extra parts came rolling out :-) It bled good using just the hand vacuum...

I wonder if the PO "back-bled" from the nipple, and that is way it is on the bottom. Searching the net -I have read of success for some owners to ramp up the front end or hang their truck from a tree. hehe I think I am going to park on a hill, and try that, then if I still can't get it I will...

Thanks for all the replies. Oxides, you mentioned the slave is installed wrong. I noticed this too, I have never changed a clutch slave, can I unbolt it, and rotate it 180 degrees? I tried to switch the pipe and the bleed nipple around yesterday so the bleed nipple would be at the top, but they...

no, I will look up the correct way to do. hope I can do it from inside the cab as the resevour is mounted to the inspection plate and has solid lines to it.

I have a board wedged on top of the peddle now. gave another attempt at bleeding with the hand pump vaccum tool, then just did a bunch of 1/4 inch long strokes mid range of the "full cycle" and holy moly- I got to some resistence, It felt like my old clutch!The status right now is about 2 full...

no, nothing of pressure coming out with the 2 person attempt. i will leave the peddle down for 24 hrs and report back. Is it possible I have the adjustment wrong for the peddle and plunger part?

I just replaced my clutch master cylinder. The peddle has no resistence, I don,t think it is bled properly. I have tried the 2 person method, one pump and one bleed, I have also a hand vacuum pump that I can get a 15 PSI vacuum with. Nothing is coming close to getting a resistive peddle. By the...

Thanx for all replies, and jcuk for taking time to upload the photos. I get how it works now, will be ordering 4 of them. Cheers all

Hello, can anybody post a picture of your sliding window locks? I have a button ratchet type for the very back windows, but nothing for the sliding windows on the 4 doors. The doors lock, but not the windows. I want to order part #332435. How does it work, is it easy to install, do I have to...

The spindle wore on my original Zenith allowing petrol to leak onto the manifold and engine, so I replaced it with another Zenith. Ran great at first, then it slowly progressed to dieseling when shutdown, black smoke, no power under load. Took me some time to find out why, but the piece that is...