Search results

I've got an OBD reader but it's one of the cheapy/generic ones, what values should I be comparing with? O2 sens voltage?

Morning, Just took mine in for an MOT. It failed on suspension wear and emissions: Exhaust carbon monoxide content after 2nd fast idle exceeds default limits (8.2.1.2 (b)) Exhaust Lambda reading after 2nd fast idle outside specified limits (8.2.1.2 (c)) Exhaust carbon monoxide content at idle...

Thanks! Been out today and drove about 20 miles total, all seems to be good so far. I did smell some burning from under the bonnet, maybe because the heat shields are off? I tried to check the coolant level when I got home, but now my bonnet won't open 😑 only pops on the passenger side!

Unrelated question, but does anyone know what this connector is for? Been hanging disconnected since I got the rover. Driver side of the boot lining.

Top hose was cold and squishy this morning. No obvious leaks either, so fingers crossed. Next issue is why my battery doesn't last more than a few hours, but I'll save that for another thread

I'm guessing it should still be hard by the morning if the pressure is holding?

I haven't got asbestos fingers either, it's a very quick squeeze to avoid 2nd degree burns to my fingertips 😆

Top hose is hard but not rock solid - there is a small amount of give when it gets a good squeeze

Just been for a 10 minute drive. Temps idling between 90-91, max 92. I'll keep an eye on the levels and for any leaks. Only thing that concerns me - assuming the OBD tool is correct - what kind of damage could have occured if the temps were actually at 118ish?

That was too expensive 😆 Hopefully the coolant doesn't spill out when I hoover the carpet next...

Just had another go. I taped the end of my hoover up and created a makeshift slot for the rad bleed pipe: And after I filled up to the neck of the bottle, I stuck the hoover on for a few seconds. The level in the expansion bottle quickly dropped, so I topped it up to the neck again. Hoover...

I've got 1/2 the vacuum kit, just missing a compressor :( I did blow through the hose too. I'll have another go today

Would it be unwise to put the hose directly in to the cabin heater pipe and give it a good blast?

I believe I followed the RAVE method: - Drained as much as I could via rad plug - Slowly filled expansion tank with a hose on a small stream - Started engine, monitored level, waited for thermo to open - Stopped engine, waited for it to cool, topped up expansion tank again. I believe that's...

Just been out again and ran it for a while with the cap off to let any air escape. Still idled in the middle of the temp gauge. I noticed that the right side pipe to the cabin was hot, but the left side pipe was not. Possible air in the cabin loop?

Just went out again and topped up the water. Ran for about 10 minutes, temperature reading on the device was in the high 90s, possibly very slowly creeping up. Dash temp gauge in the middle. Noticed the blowers weren't that hot, so possible that there's still air trapped somewhere. Is there...

Needle was in the middle on the temp gauge. Don't say that now - I don't want another warped head on my hands!

It seems to be running fine - but I haven't left it running for too long just in case it was getting too hot. Upper rad hoses were scalding to the touch, but not rock solid, only quite hard. Once it's cooled I'll double check the levels and give it another go.

No leaks overnight. Drained coolant today via rad plug, and slowly refilled with just water for now. Followed the process in RAVE - but when I ran it again the temperature was averaging around 117-118C, which is decently outside normal range I believe? Reading was made via obd tool - temp...

I've pumped the tool by itself, will keep an eye on it. Finished reassembling, started up and seems to be running okay. No leaks so far. It did start to overheat after about 10 minutes, but I was expecting that because I haven't refilled the coolant properly yet. Will try tomorrow and see how...