Search results

The GAP are a bit frumpy about replying to help particular problems . However I think I need to formulate a query with them .

No not contacted yet . Yes the same , three pin , Brittpart

No not contacted yet .So I have included a couple of photos I have extracted out of the GAP manual . Maybe try again on calibration , guided maybe , but have done this and got the error E16 . GAP CONTACT NEEDED! Yes that is the part I replaced from lrdirect , once fitted the orange anti roll...

Yes I have done , avoid that is . I Flashed the engine ecu before when I requested the standard mapping from GAP , as when I bought it the owner had it mapped for power and economy and it kept giving a fuel regulation problem . Anyway I digress , it worked . Back to this I have tried tight...

I get the facility to re-enable EAS as you say I may be missing something. I'll have another look , there is a facility that I can flash an ecu , suffice to say I have avoided it so far , might be brave later! "thinks" that you replaced the module, if you have a configuration option for the...

I saw a guy on you tube resolving the code I get , Sorry the pic I put on is not very clear its Code C1A00-54 and he puts the fault down after calibrating height after sensor replacement then it muddles the Suspension module , he suggests putting the Susp. system out of tight tolerance to...

Doing guided calibration on four corners will complete , an error E16 appears on GAP . Got to Active Roll cal and e red error appears on the dash and this faultS I will try battery reset , there seems to be a confusion between modules Yep done that

Apologies for repeating my thread , did it last night and couldn’t see it today , so wrote a different version lol!

Yes it does , will try that first today .

What’s the best way of resetting the ecu that controls the height on RR. Now that the new height sensor has been fitted and the suspension over 4 days had dropped to one side it doesn’t want to play. Switching up or down the car goes to opposite levels though some of the height has been restored...

New sensor fitted , no warning lights as in Suspension and dynamic roll , all faults cleared , but vehicle still leans to the right as after 3 or 4 days waiting for the level sensor the air supply had given up. After installing the sensor the computer fails to synchronise the four corners...

No not necessarily, only verified that the new sensor I had by chance is showing a varying voltage when moving the small arm attached, but at least it proves that the modules might be a bit happier. I will see if whole the new borrowed sensor clears the whole list of module communications ...

Looks like faulty sensor , plugged a new one I had for front and it shows voltage on the diagnostic .

No in general the roads are salted here a lot because of our weather .up here, before my ownership who knows , I have owned since 2021.Anyway the plug is off just now and Ill clean with elect contact and put back on with some Vaseline around plug shell and try diag clearance.

So the following tell tale signs of the height sensor playing up . Hopefully will find the fault today .

No its not the same , , a whole heap a module mis matches then when cleared the one that remains is under suspension , the rear right height indicator . Still the same Dynamic roll light which go out on occasion All back together now but will have a look , its just a lot of work to remove the...

Hey HO it didnt last ! One week and now the modules connected to give messages to Active roll , decide to give out a bad connection from the rear height sensor and threw out the the roll light to amber again.

Spray ordered!

At C2396 male half , and check resistance back to pcv , on the block , this at 5.0 ohm . Individual line check back to module with green plug off, 0.3/and 0.5 . A good deal of wet around the perimeter of C2396 . Will dry off and reconnect. 1hour later plug cleaned with electrical cleaner , no...

Measured at green plug C0647 and the purple -green/black is measuring 1.4 ohms, tried at the back and front of pins . So not sure what that means . Also tried to use the trigger but not sure if that works or indeed I know how to to be honest .