Search results

Evening all, Has anyone got a definitive answer to the quantity and order of the rocker shaft washers on a 200 tdi? The photo below shows what came off mine, which matches a Britanica Restorations video, but parts diagrams seem to show more/different order. With another diagram showing qty of...

They're bolts..

Last photo looks like timing chain parts

Thanks for the post, I actually got myself a 200 tdi which is undergoing a full rebuild currently, so thanks but I'm all good now!

Afternoon all, Another chapter in the 200 tdi saga. Whilst getting the crank gear/pulley off (very tight, needed a puller), the timing case got a little damaged, as per photos. A bit of crack and the hole for the oil seal is slightly out of round. Any suggestions? Waiting to hear back from...

Thanks for affirmation, have contacted the seller who's sending a new one out.

New gasket arrived slightly bent, no crease in the ring but looks to be coming away from the gasket slightly. Tempted to put it in knowing the pressure from torquing up, but would be good to have opinions.

Wasn't quite happy with putting it back together knowing the cam was stiffer than it should be. Took a razor blade to the shiney spots on the cam bearing and gently reamed it down, took a few attempts but now turns freely with only a small amount of bearing removed. Core plugs back in and...

New bushes arrived today, much easier to fit, straight in and easily aligned. However, bearing no. 1 is a little stiff to turn, tried shifting it back and forward a couple of times in case it was misaligned but didn't help. Tempted to carry on with the build and hope it beds in slightly...

Your 101 is terrible, but if it's genuine have you contacted the RNRMORT?

No... I hadn't seen that! Thanks Steve, that's helped a lot. The most frustrating bit was using the Turner split bearings, as you couldn't tighten the tool without opening the bearing up too much to fit in the opening, then you also had the ridge when fitted. So I'll use the suggestion from...

So it turns out installing new cam bearings is a bit of a pain. Took a while to get each bearings lined up with the oil port in the block, taking a few attempts with a couple of the bearings which didn't help the finish. Bearing no.3 now had a ridge where the split/gap is on the bearing...

Afternoon all, I'm looking to swap my original 2.25 diesel ignition barrel (w/ pull to stop) for a Defender barrel giving the right terminals for a 200 tdi conversion. Can anyone confirm which part numbers actually fit the Series steering column? The research I've some has suggested there are...

Thanks, I'm at the point now where I need to draw the line in terms of spending really. I think I'm going to put it back together with new rings, hone the remaining cylinders and see how it runs. With the little use it's going to have I'd rather take the chance than spend another few hundred...

So the staining cleaned up, but there's a slight bit of pitting you can just about feel with a bare finger. I know it should be bored and lined, or oversized piston, but I'm tempted to put it back as it is and see how it runs. Edit, rings are out of spec so will be getting replaced. I'll call...

Bearings weren't too bad but I've got replacements for them all along with camshaft bearings. So it seems a bit silly to not change the rings while I've got it all apart, but I need to draw the line somewhere as I've just bought a new house and can't keep hiding money from her 👀

I'll have another attempt at cleaning the staining off, but it didn't seem to shift before with an oily rag. Not had rings off the pistons yet to check gap, that's a job for tomorrow. Fingers crossed I'll have a couple of honing tools to borrow tomorrow too, so if it doesn't shift with another...

Yeah I'm surprised at the condition of the cylinders considering how bad a state it was in externally, dirt, rust, seized pulleys etc. I've got a couple of honing tools to try this weekend, might also give it a rub with some light polishing compound, or valve lapping paste?

Will update when I've done something, it's going into a Series so won't do more than 3k miles a year, but while I'm at this point I'd rather not cut corners.