Search results

Thanks for the guidance, it's as I thought but needed to get confirmation as some things I do seem logical but then I screw up..........it happens The spill pipe I have is 3.2 and I have fitted it and it works The problem I am having is the leak off pipes don't want to seal and seem to be...

That's what I was thinking but if it is given enough time to dry/drain it should be OK don't you think the gunwash I have never used so don't know what it does The problem I have is I was a diesel fitter military trained and worked as an MOT tester etc etc prior to me becomming ill, it is hard...

Update Spigot clear, I don't feel it is the wastegate as it doesn't feel like it is over boosting, it feels like the other way I am going to try fitting the other two pipes from the left hand side of the intercooler when I strip it down to clean it up as I have done the one on the right from...

I will admit I am still learning and as I have FMS and spinal issues memory is very poor and any activity is a big issue for me so things I may have known I forget or need to re-teach myself on most tasks....................so sorry if I mess up when I post I am only human. I have checked the...

I have not checked to see if the pipe is blocked, I will do that next I have just tested the 3 wires on the map sensor power 5 volt ground and sender wire. I get 5 volts from the power wire and 1.7 volts on the sender wire, I believe this should be 5 volts and it drops depending on the vaccum...

Sorry, missed this, no warning light on the dash when it happens

Hi Guys Thanks for all the advice as always. I am going to clean the intercooler system and change the fuel filter and air filter as part of the service but I might have discovered the problem I disconnected the MAP sensor and took it for a run, it runs smoother (no boost as expected) but it...

Thanks, I will check the suggestions tomorrow and report my findings I had intended to do the intercooler but what is the best solution to flush the intercooler rad? Thanks

I am sorry if this has been covered before but I can't find any link that covers what is happening to my P38. It is the Diesel M51 BMW engine none egr and I will explain the problem I have If I drive normally the car drove fine, then I found that the air in pipe to the turbo had come off and...

As promised I said I would report back to the group To keep the costs down as it was unknown if the part would be the problem I have bought items from eBay. I know the risk is that the parts can sometimes have issues, but I discussed with the seller to ensure that the part worked and if it did...

Hi Just a heads up, if you are offered this please let me know (pictures attached) I had a good spare alloy and brand new tyre at the front of the house, under my bay window I have just come to move it and some sod has nicked it Not that it is worth too much but some thief has nicked it from...

Could the outstation be a cause for the issue that I am experiencing If this intercepts the signal from the BECM to the door latch and one of the plugs had been slightly wet, would it be a reasonable assumption that the outstation might not be causing the issue between the RF receiver and the...

Does anyone have any idea on if the door latch is the problem and how is it best to test it once it is off Thanks

If you have not got the tailgate trim I would suggest my parts man He said to me that the screw clips are always damaged so I used double sided gorilla tapeto fix it but if you give him a text or call and tell him Dave from Preston gave you his number His name is Paul Johnson 07885269472

Another update Took the door latch off today, that was an experience. I must admit that I screwed up in that when putting it back together I didn't have another door or window open..................you can guess what happened.................Yes I let the door close and the handle wasn't...

I know what my next job will be, at least then it can either be ruled out or ID'd as the cause. As always I will report back to the page on progress. Fingers crossed I find it soon as it is starting to wind me up.......lol I assume the door panel has one screw where the internal door release...

So "Datatek" you are saying that the fault may still be the door latch and the microswitch? Never having stripped out the door latch mech I understand that there are a number of types of door latches and some are more prone to fail than others? However, it is said that if you can put in the...

Additional Voltage test on green dot 10.5v static no change when key fob pressed Voltage test on 1st blue dot 10.5v static 6 to 8 v when key fob pressed Voltage test on 2nd blue dot 10.5v static 6 to 8 v when key fob pressed Any thoughts?

Update Wire in the O/R plug on the blue plug and I get 10.55v reading when nothing is happening Then when I press the remote I do get a drop in voltage to what appears to be 6 or 8 volts Not sure what that is telling you Marty but it just confuses me more. I assume this is saying that the RF...

Another update following Marty's advice Attached are the pictures of the plug and pins, again they are clean, tested continuity and I get a good tone. I put the green dot RF receiver on and nothing (I assume this has failed) I put the blue dot on and synced the key and as before I get one or...