Search results

Fitted new speed sensors, bought a new ohm meter, reconnected battery this morning started up runs well on the button, but then it happened dashboard lights up like its Christmas again, big F loads of different codes tried ohm readings from abs pins to sensor's r/l 1.080m r/r 1.065m fronts with...

Bit of a result only one light left on dash and two codes which are temporary, haven't had time to put the wheels on yet, hoping to raise suspension, cycle gears and fill the trans with it's remaining 3 litres, and at least move it remaining hopefull, as want to get the xf in, undertrays and...

So instrument cluster and abs are the ends of the loop, now I know the pin numbers will test sensor harness for continuity abs plug to sensor at some point and possibly clean the rear hubs too many thanks for your help will keep you posted

Thanks mate just what I was looking for your a star will help me get my head round it, already sust that sensor supply and signal go to the abs so can now check continuity, plug to abs will work through issues over next few days, sensors arrived but couldn't fit them into such a rusty place so...

Sorry ment to say can you reccomend a breakout box something else I would like to learn about many thanks for all you help and advice waiting for sensors today and rear valve block tomorrow many thanks mate

You always help in a big way mate, many thanks. Front sensors read 01.1 on 200m setting, but on 2000 settings reads 489 but the damaged one flashes to 1650 then goes blank?, all readings otherwise the exact same on other three sensors on both settings will let you know readings on new ones be a...

Hi mate waiting for new speed sensors before scanning again ap200 is spot on thanks for the heads up, where I'm at, found a bare wire on r/h sensor, ordered new fronts also want to check the ohm reading of a new ones arrive today, rear valve still on until new arrives, old one is constantly...

Yes abs unit and valve block's only at this point suspected and concentrated on, waiting for a rear vb before removal

Run through all plugs today cleaned with electrical cleaner nothing untoward. Used cleaner on the outside of the plugs to help to free off the little clips. Visibly all looked ok, checked out speed sensors as this could explain at least two of the codes I think, one was faulty and damaged but...

Yeah your right couldn't miss this one lol, ordered two new fronts as their out, l also want to check ohm reading of a new one for reference, but do have a gut feeling this is not the only issue but fingers crossed

Found this r/h speed sensor no ohms bare wire and a join hopefully this is it l/h to check

Quick update be gentle not an auto electrician checked rear speed sensors both read 01.1 on this setting in pic both side exact same am going to clean sensors and all plugs in these areas then move onto front

Hi mate going to look at valve blocks and speed sensors and plugs today thanks will check and clean plugs behind headlights, previous owner did quite a bit of damage removing stuff maybe a wiring issue, going to put on axle stands wheels off liners out two already out ohm test on abs sensors...

Thanks mate will check it out

Will pull out the liner tomorrow check out the wiring too will run through it piece by piece

Yes their all basically communication codes will work through plugs and the obvious first, yes front valve connected, going to switch it out as still accessible nothing seems trapped so far, one strange thing since last post would like to ask you about if I may, strange light constant ticking...

Hooray it runs, but has a couple of issues to work through, steering stiff but pump turning will have a look over next day or so, but getting a few codes v0416-94. V0421-94. C1a32-01 and last but not least V0416-86 all communication issues any one have a starting point? Going to check abs plugs...

Thanks mate much appreciated

It finally happened a glow connection plug came off in my hand, am I right in thinking if I check their orientation against my 07 I can simply plug them back in to the plug? if you see what I mean, I have a spare heater plug harness could plug in and test for power?

Getting there don't have good finish like yours have brushed it on quite thick, prep is always the longest bit and every piece of dirt seems to find it's way into my eyes even with goggles Lol