Search results

Noticed that the battery 0n the testing 09 is 85ahr 680amp, D3 spec says 95ahr 850amp so have ordered correct specification exide, might this make significant difference? 07 all good but elchepo compressor needed Hitachi software not direct replacement as advertised, but works fine, started on...

Fitted wheel bearing was tight extremely, pushed out hub, had to remove inner then weld around the outer inside race causing it to shrink did the trick went back together with a new backplate ok, Busy day today refitted bearing and new compressor on 07, seems ok leveled suspension, rears still...

Many Thanks mate plug first will check for canbus and power/ wiring, have 60 ohms at all plugs checked, also looked at it awake too couldn't help it, tested fuses for power tested all relays relevant or not, will check this plug while the motors out in future, will also recheck transmission...

Hi can anyone help? Trying to find atcm location probably looking in wrong places, going through system getting 60 ohms at every canbus location, now have only communication issues with the atcm, heads up would be most appreciated

Useful information and pictures, may I ask what was the fix? Cleaning board/pins etc or replacement I presume

The reason you couldn't stop the motor was running on its oil being overfilled drawn in through breather, can cause significant damage, in many cases, hopefully you'll get lucky will need significant cleaning as mentioned above

Found a very sketchy rear wheel bearing on my 07 today removed the hub and cleaned abs sensor and ring areas, was probably a quarter of a teaspoon of rust stuck to the sensor so cleaned up, will do the otherside too at least clean it, removing and fitting bearing tomorrow borrowing the local...

Hi did you change Hitachi like for like or was an amk fitted

Hi mate yes every thing nice and clean but will recheck power supply at unit etc when I refit nothing seems untoward so far, raining today but going to refit unit tomorrow and start rechecking everything, have a nagging feeling I may have diagnosed the wrong module being honest with you, at...

Oh dear no fault found back to drawing board?

As suggested re-downloaded ap200 app on my phone, used wifes before as it was newer model, low and behold calibration works, so tried to go through instructions, threw up c1a00-54 control module, put this down to me messing with the ride height so had a cup of tea tried again this time worked...

Never thought of that will re install, pretty sure I have gotten all my suspension info from you mate, will fiddle with it futher this afternoon, yes shame you don't live round the corner although I might be a pain Lol, can always get mate from garage to calibrate, doing pre mot work/check on a...

Sorry got cut off, still to run live data, keen to work out issue rather than throw parts at it, once suspension issues resolved most likely will sell it keep the auto, couldn't calibrate with autel this morning in touch with help desk, I have most likely done something wrong when registering I...

Yes mate not much left, getting there no lights so is on the mend I hope, what confuses me is yesterday i only changed the compressor basically 2 off one on, as you know only one hp pipe which wasn't leaking any way last night suspension stayed up perfectly, s

Changed compressor yesterday found leaks on the one I had fitted had corrosion, so, changed to one I had from a 06 fitted new dryer beads o rings etc fitted took for drive amber light pops back on, pressure to low code, so "borrowed" compressor from one I've just rebuilt, used last night no...

Landrovers together in front yard still have under trays and wheel arch liners/trim to fit, discs/pads and have a leak off pipe leak to do, abs off to ecutesting.com for repair will bleed and do brakes on its return with ap200. Back on 07 tomorrow have ordered a new reservoir block, and going to...

Messing about with last few jobs before moving it out of the workshop, autobox arm to cable had seized so stripped cleaned and soaked in oil for a bit works fine now, had a power steering issue but seems to have resolved itself think it must have had an air lock, no puddles underneath and it...

Thanks mate yes took me a while but just found it on d3 website vdcm and abs same thing, think its coded, but not sure, only codes I couldn't clear was vdcm, your help with resistance tests confirmed continuity from abs to wheel sensors, and can bus link was ok so was starting to suspect abs...

Thanks mate changed rear valve this morning compressor ran for a while, then the fickle finger of fate happened, my friend from the local garage turned up needing a 2.7 injector so we did a Norfolk barter, he agreed to come back with his diagnostics, he turned up about an hour ago, blew up the...

Yes thanks mate canbus seems intact will check further, canbus wires are spiraling in the loom?. motor runs sweet, locked in park, still needs 3L transmission fluid, no suspension now has some pressure in bags lifted slightly then compressor cut out warning back on dash, can't make sense of...