Search results

Let’s see the pics!...

So mixed bag today... Handbrake adjusted and now would hold like Spider-Man’s underwear...cable is adjusted right out to max so will need replacing but should be fine for MOT Sure enough my intermittent heater problem was indeed this little devil. It was blocked completely and holding around...

Thanks gents for all the input... Went for a family drive on New Year’s Day...it was Baltic. To my surprise and delight when I tried the heater the bloody thing fired up. The Mrs was most grateful for the 200’s decision to oblige with some warmth...let’s just say they don’t have the best of...

Hum...certainly have had a lot of rain the last few days but it packed up last week?...will check though Think I will pull the heater box and have a good nose about

Havent checked but it certainly was when reassembled after matrix replacement..I will check again. Can I ask why that would make a noise when the heaters fire up?

Thank you for taking the time to respond and in such great detail. I have ordered a relay kit via the bay with the modified resistor to speed up the slow setting hopefully this will rectify the gremlins and have the cabin fairies ( my lasses) all nice and toastie again. Should I be worried...

For further info the By Pass of the fan control switch is successful when joining black with 2nd stage green purple wire but not when joining with black with 1st stage green yellow?

Update Have had another go at the bypass of the switch and this time the fans came into life without blowing the fuse. (Must have had a poor connection or bad test wire previously) So now Disconnect the relay/motor wires and the fuse doesn’t blow when switched on (No Fan obviously) Bypass...

Hi all, having problems with my heater. The minute you turn it on it blows the fuse. Hoping you guys can help me diagnose the problem. The heater box was given a bloody good clean when I replaced the heater matrix a few months back I have 11.86v at the 2x wires that go to the relay/fan...

Is struggling with his heater

So...it all turned out to be crappy hazard switches after all. I eventually but the bullet and sent it to the local Landy whisperer. 4x different switches including new Lucas OEM units and they were all utter crap! He made one good switch with the parts of all the others and all was well...

Should’ve updated sooner. Always frustrating when searching threads for advice only to find no conclusion. I used Dishwasher tablets to flush the system...cheap as chips and very effective

Appreciate the walkthrough...I have 2x multimeters for some reason. Both digital but neither with a beep. Really am annoyed as I was so pleased to get the indicators working following the previous hazard switch fault. Whatever I have done I now have a problem with them too!...so frustrating...

Thank you for the picture post

Have given up for today... it’s really done my head in. There seems to be one communal ground point with 2x black wires leading to the rear loom wires right next to where the loom comes into the truck. Apart from that grounding which appears ok I can’t see where else to check

Ok so I’ve spent the afternoon poking about but to no avail. In fact I’ve gone backwards...I tried simply splicing the wires as I originally found them which resulted in the fog light functioning but still no indicators and my hazards blowing the fuse. I’ve now disconnected the splice and...

Yes I have a multimeter but no experience of using it for much more than testing batteries

Update...several flushes and a new stat and the cooling system is now clean as a fax doorstep challenge. Seems the seller was throwing a straight hand. Have since also replace the heater matrix & now have a 200tdi that actually blows warm (ish) air

Hadn’t thought of that , to be honest been over thinking it. What would be the proper fix? At present I’ve rerouted the fog light -neg to the loom cluster where as before it was attached to the -neg of the indicator wire Is there a better fix

Hi all, I have a 1994 110 CSW that is driving me potty at present. last week the indicators just stopped working without rhyme or reason. I was able to diagnose it as a hazard switch problem and after installing the new switch+ a new fuse everything was up and running. Now the weather has...