Search results

I have bottom door seals that I want to fit to my new front doors. My vehicle is a 93 200Tdi, but my new dorrs are the newer Pumer type. I have seals that where bought (by previous owner) for the original doors. Offering them up they line up with the pre drilled holes in the bottom of the door...

Thank you Mick. Val.

I'm looking for the little screws that hold the window trim in place, so I can get on with assembeling my new doors. Ordered some loose screws from ebay, turned out to have the wrong heads (really crap photo is my excuse) Ordered some more loose (with a better photo) got the wrong size, way too...

Thanks Guys. The Flashband although I think it's too thin, did point me in the right direction. I found butil based pads for insulating and sound deadening campers. Ordered a few sheets of that. Should work nicely. Val.

I've been looking for the anti drone pads that stick to the inside of the doors to stop noise vibrations. They are the bitumastic sheets similar to thouse found on the underside of your common stainless steel kitchen sink. Nothing comming up when I do a search on this forum or ebay. Anyone know...

I'm building up my new doors. I need a bracket https://www.lrworkshop.com/diagrams/land-rover-defender-body-chassis/doors/front-door-assembly_52667 Part no2 on the diagram. I've tried Britpart, Bearmach and ebay with no luck. Any ideas? Ta Val.

My 93 200Tdi has been rebuilt with polly bushes (I'm told they are a softer type of polly, don't remember what they are called) and standard weight springs with a small lift, along with Oldman Emu shocks. The ride is harsh and jaring. So If I fit adjustable shocks. Will this soften things up...

Bit supprised some are worried about rear end collisions, when the 110s and the moderen 90 TD5 on all have the rear tank. If this was a real concern then a side impact to the older 90s would surly have the same effect. I was just wondering if it was possible to do this as I've seen the 110s and...

I saw they where different and it got me wondering. Fuel tank is a lot smaller than my discovery two was though.

I have a 93 200Tdi 90. The fuel tank is under the drivers seat (partly anyway). I've noticed that the 110s have the fuel tank at the back. This is also the case for the TD5 and Puma cars. Being that the rear section of the chassis is likely to be similar on both the 90 and 110s, Is it possible...

Bought a pair of these. Alli skin and fitted fine. Only difference is that they have a fixed bolt on one of the window carrier panel fixing where the old one (93 200Tdi) it's a fixed nut. No hassel, I'll it still fits...

I bought my 200Tdi with LEDs fitted already. They look good on the car and are much more visible to others. However every so often the indicators flash outside but the dash light doen't. Following behind the LD one day (I do let the wife have a go now and then) I saw that both rear indicators...

Yep, That would probably solve the problem. Sadly my hinges dont have a slot for the tab. My thoughts are: 1, Somehow try to peen the end of the thread to stop the nut falling off. Though this won't stop it undoing most of the way. 2, Thread lock. 3, Second nut to lock against the first. 4...

Would need to be a very thin nut. Have looked at using two nuts and locking them together. Very little extra thread to work with though. Yes thread running through the nylon. However the bottom hinge pin does not sit in a deep recess like the other two pins, so the pin doesn't stick put the...

So. I bought new a new hinge bolt/pin kit with nylocks etc. Fitted them with plenty of grease on the ball. Nylock nuts on the top amd bottom hinges are working loose each time the door is opende and closed. ffs. What did you do to stop the blessed things from coming off???? Val.

Thanks Guys for all the info. I had the new and old doors side by side today. Those little black clips are the ones I need and the white locators that they go into. Corse, Now I've run out of time for a few weeks to fit everything together. Next weekend is ear marked for replacing the power...

Thanks Mick, Had a good look around the Paddocks site. The plastic bits are different from the ones fitted to my car. I'll have a colser look at the new doors to what I need. Val.

What are they called and where can I get the little plastic screw fixings for front doors, that hold the inner door and other parts on to the main door? I'm fitting new doors and will probably break or loose some of the 26 year old plastic bits if I try to remove them. Ta Val.

I've got the Freestyles with BFG AT's I guessed they where 30 odd Kg's, cos it near broke my back lifting it off the door carrier. Eventually got the swing out weighed. It came out at 19.5Kg postage thoruge DPD worked out the best deal. The carrier is quite a robust looking thing, swings...

I need to sort out postage for a swing out spare wheer carrier. Does anyone know what they weigh roughly? Ta Val.