Search results

i suspect you were dealing with idiots. i have never seen a new or properly reconditioned turbo which was tight to turn.

Hi Shane, Have you counted the teeth to check they are actually 4.8 and are they land over diffs/axles I cannot find any land rover with 4.8 ratio only thing i know of with 4.8 was a few Nissan Navaras. look here http://www.difflappingqld.com.au/uploads/web/gear-diff-ratios.pdf

Always welcome an electronics expert. Hope your cooling issue is nothing too serious. I would start by checking all pipework is connected correctly as it is possible to refit some incorrectly when replacing components. I think blocked heater matrix will cause overheat on td5 so check heater works ok

pardon

am loving the motor. Welcome. The guys here between them know everything about series and will i am sure answer any questions you have

Hi I am looking for an overdrive unit for a 2005 defender td5. Anyone got a decent used gkn or roamerdrive they wish to sell?? I am based in midlands but can collect from pretty much anywhere within 150 miles or so

I think it is 70 ft pound. If pump is off the engine hold coupling in vice with soft jaws. If it is on then ideally you need a piece of bar with holes drilled in it to bolt to hub. As long as coupling did not fall off it will not move. When we used to pull them they are so tight on taper they go...

From memory there is no key in the drive coupling but the coupling is securely locked on its taper and even with nut off takes lots of force to remove. When the coupling is fitted originally the fuel pump plunger lift is set with keyway in shaft approaching number 1 cylinder using a dti...

Not sure how easy to fit but maybe easier to find a 3.0 litre six from a P5. If you can find one of the last ones with the Weslake mods from the manual version you would be looking at 134bhp and 169lb/ft at 1750 rpm. I had one in a P5 Coupe silky smooth and almost same power as the v8. Not sure...

I think they should all be the same.(see image) You can always measure depth of holes just in case o nly one part number it seems

Seats in 2005 just have two pin plug the seat heater has a thermal cutout so all you need is power and earth. the switches look same as images loaded by Wimblowdriver. I have included wiring pinout if you have genuine switches

Apologies in advance I know this has probably been done to death but...….. Have any of you good people tried one of these kits as I am considering one for my td5 https://lofclutches.com/does-a-solid-mass-damage-a-td5-engine-pros-and-cons/?v=79cba1185463

I like these lol https://www.bing.com/videos/search?q=detroit+v8+diesel+engine+sounds&&view=detail&mid=E89E41EF4BF4F8792A53E89E41EF4BF4F8792A53&&FORM=VRDGAR

i use a disc lock,alarm,tracker and one of these https://bulldog-secure.co.uk/shop/bulldog-security/bulldog-ca2500-centaur-wheel-clamp/

Yes it has a pipe instead of a breather hole. Mine working just fine. I guess u you could put a length of tube on it if you want to mitigate against fuel all over engine should it spring a leak in the future

hi If its from the 13mm nut next to "559" stamped on housing it is a lock nut for governor weight support spindle. the spindle has an o ring inside the housing and is adjustable but DO NOT take it out with pump in situ as the governor will fall to pieces and drop inside pump. Pump should come...

broken bronze cam follower slide?

I will do you a straight swap if you like

you can use five piece compression fittings to join nylon to metal pipes. The most common error is not using the correct olives. Use stepped olive for nylon and barrel olives for the metal. Sorry if I am stating the obvious.