Search results

The lower oil pump filter bases shared the same bolt holes so you can swap filter housings between Rover V8's. The issue is that the filter will be mounted in different ways usually for clearance to front axle, chassis legs etc.

The biggest issue with earlier Series models were the seatbelts which had the shoulder strap secured to a fixing behind the top of the front seats. In a head on collision the belt would compress downwards resulting in serious shoulder injuries. Later hard top models had the shoulder strap...

No pin in blue box. Red box uses a pin in some earlier Series 2 models. If you're disassembling them, you can remove the 7/16 hex bolt and screw in a grease nipple. Makes a difference...

You seem to be having too many oil leaks. I suggest checking your crankcase breather system. If its not venting vapours/pressure, you'll find oil leaks everywhere...

A red top will be fine. The carburettored RRC had them as OE fitment. I'd suggest putting a filter ahead of it so you can easily see if it's dirty. They have an internal filter (behind the hex cap) which cannot be easily monitored.

I've had SU's on my V8 Series for decades an I've never had any issues. Certainly nothing heat related. They're off an SD1 and run on a dead head layout, so there's no return back to the tank, just a feed from the pump. I've an electric fuel pump bolted to the transfer box with a generic plastic...

The ignition amplifier must have an earth, through its two mounting screws. Its relocation is a very good idea but relying on the inner wing of a RRC as an earth can be a gamble due to corrosion. I'd suggest running a wire from the amp and earth it on the dizzy if it has a male spade poking out...

I was having a pint recently with a very old friend who has been working on classics for 50 years. He's of the opinion that positive earth vehicles rust faster than negative earthed ones. Any ideas on this??

There's a very thin wire in the distributor that earths the points baseplate to the distributor body. This can break, resulting is nothing happening. At this stage I suggest establishing if your coil is correctly wired and firing. Step 2 is spark distribution. I have been plagued over the last...

Ill assume that it's unknown if you have a pos or neg earth coil. To isolate the fault I would suggest the following: Put a plug lead into the coil HT connector with a properly earthed spark plug at the other end. Turn the engine by hand until your points are fully open, as this prevents getting...

Hello Datatec, Correct the VC is sealed, but in the many RRC and P38's that I've seen, the BW transfer boxes have lasted for more miles in the Classics, which have Dex 2 listed. Again, just my opinion from experience.

Two last things to check: The BW transfer boxes are know to be very quiet in operation. If the internal chain has stretched it will make noise, and can eventually lead to total loss of drive. Check that the yokes on your front prop are in alignment. Depending on who did the conversion you might...

Also, if you have the original Series 2 front axle it will have universal joints in the swivels, not CV joints like a Defender or RRC. Now being full time 4WD, the UJ's can create a kind of "shimmy" when going around tighter turns due to their design. It will work, but it will never be totally...

If your viscous coupling has seized you'll be chirping tyres when turning on full lock. It don't think it's seized based on your description. Only Dextron 2 for auto box and transfer box in my experience. Dex 3 is too thin and not suitable for 4HP22/BW viscous transfer box. Many unexperienced...

Be careful with your wheel nuts/studs. Landies pre 1970 (not fully sure to the year) have smaller wheel studs and nuts. They are designed to share some weight through the round hole in the centre of the wheel. The studs are not designed to take the full weight of the vehicle and are not safe...

Here's a pic to give you an rough idea. I have used an angle grinder in the past and it's a simple job. It's important that the new spigot bush bolts to the flywheel without touching the end of the crank.

I have done several of these conversions so feel free to ask more questions.

The Disco/Range Rover pressure plate is too big to fit into the Series 3 bellhousing. You will have to get your flywheel drilled/tapped to accept standard Series 3 9.5'' pressure plate and use the standard clutch disk. Any machine shop can do this for you. Whose kit are you using for the...

I had similar problems sourcing service parts for the Mazda SL35 fitted to my RRC. The Mazda and Nissan diesel conversions were very popular in the 90's. They were also both fitted to many forklifts so finding gaskets and internals should not be a big problem. You could research if Motor &...

Make sure that the stop lever on the fuel pump is fully returning to its rest position after you release the pull stop lever on the steering column to kill the engine.