Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. M

    Code P6050

    Maybe I explained poorly, If I change the ECM, and if it doesn't work, I don't do anything. I exchange the old one back, does it work as before the exchange?
  2. M

    Code P6050

    Can I start the car if the oxygen sensors are disconnected? I was just wondering what readings I would get with the bridge's Ican tester
  3. M

    Code P6050

    Thanks for the answers! If I change the ECM and it doesn't work, will it work like before if I change the old one back, that is, will any settings change if I change. I've ordered the NCOM05 but it won't arrive until weeks later. Oxygen sensors have heating resistors. I haven't measured the sensors.
  4. M

    Code P6050

    I break the "radio silence" I measured all the wires of the oxygen sensors with a resistance meter. Everything OK. Power and ground connections connections ECM are ok. I think there are two possibilities: the ECM is faulty or the oxygen sensors are faulty as a result of 10 years of non-use. The...
  5. M

    Code P6050

    I have done obd testing three times, almost the same result every time. Does this Icarsoft LR v2.0 give the correct readings?
  6. M

    Code P6050

    Yes, there is even a comma there: A 317.50V varies little, B: 318.76V varies little.
  7. M

    Code P6050

    Those bank A and B readings first wandered recklessly between 1.5 and 317V both, the connectors were oily, I now shook them with a degreaser at first. After cleaning, the connectors looked good, no oxidation. The readings given above are after cleaning.
  8. M

    Code P6050

    Hello experts, would you be able to help with these readings, taken with an Icar v2 obd reader. Bank A : front oxygen sensor voltage 316- 317V. Bank B: 320V. O2 sensor heater 15.06 . Oxygen sensor average 46592%. Also gives a new fault code P1190 Oxygen sensor heater circuit low resistance...
  9. M

    Code P6050

    It snowed approx. 7 cm and it is 4 degrees below zero. No repairs today. I have an extra 270W solar panel. I think I'll put it on the wall with the controls and cable from it to the car plug. I defend the 270W panel, it might produce enough current for charging in cloudy weather. when the sun is...
  10. M

    Code P6050

    OK, thanks, I'll get one.
  11. M

    Code P6050

    Datatek, what kind of solar cell do you use when the RR is not in use?
  12. M

    Code P6050

    No problem in EU countries, but if I order from England, customs and taxes will be added
  13. M

    Code P6050

    I'm Erkki, I've already seen my best days, empty pocket, city Jämsä, country Finland
  14. M

    Code P6050

    I had the ECM open a while ago. Under the plastic protective cases they are indeed on stands, not soldered, also this ERR-5760 which is from my car. There is also a third chip, which is just pressed into its slot, exactly square, the size of a sugar cube, with a small tape on it that says...
  15. M

    Code P6050

    They are plug and play, you just need to be careful, they say. I would still have to pay freight, customs and possible VAT.
  16. M

    Code P6050

    Now that I've browsed the sites ECM (ECU) upgrade Chip Would this also seem to be an alternative solution to my problem? For example, Britpart publishes a 3-page guide to replacing chips. If my problem is precisely in those chips, would it go away if I install those chips, or is the fault...
  17. M

    Code P6050

    I came across the Tornado site online, which has some kind of tuning chips that promise better fuel economy and other "advantages". I understood that the chips would come in place of these chips that I have written about, and which may have a fault.
  18. M

    Code P6050

    Yes, the M27C I mentioned.... are in a separate "foot" to which those chips are simply pressed. At least in these two AMR-5499 boxes. They are under the green and blue protective case.
  19. M

    Code P6050

    Those memory chips are replaceable without soldering, that's where my idea of a possible replacement with a chip borrowed from another ECM came from. Why would you have bothered to do without a soldering iron... When I solder semiconductors, I use a Weller TCP soldering iron. Yeah, yes Icarsoft...
  20. M

    Code P6050

    thanks everybody! Printer for that 4.6. I have to read carefully because my language skills are limited.(=bad) If I hadn't connected Icarsoft V2 to the obd port and read the fault codes, I wouldn't know anything about this fault. The fault light does not come on when running. Now it looks like...
Back
Top