Search results

Found where the oil was going. Think its time to replace filter and gasket. Not like this befor so must have been leaking for a while. Then got to a natural level below gasket. Then been at a low level for a long while. Hope mating services and bolts ok. Will probably get new bolts and...

Checked / changed my gearbox oil yesterday. First time in my ownership. Intention was to change oil. Run for a week or so and then rechange with filter. First job was a bit alarming due to lack of oil. No wonder the transmission heat light came up when on salisbury plain a couple of weeks...

Eventually got all back together. New condenser , dryer and i must admit a universal fan. Rad and intercooler out to be washed out, with the confusion in my other thread regarding the revised hose connectors from the diesel cooler sorted. Bit of a fiddle but all done. Also replaced the bonnet...

Thank you. Just seems odd the oil cooler gets no flow away from it. Thats the same conclusion i came to. Thank you very much.

Hi. Must admit to be a little confused. The flow to the diesel cooler has a restrictor. There fore there must be a flow from the rad. On my rad the small pipe with a flow is not the bottom but the next one up. Also it follows that the flow from the oil cooler is now blocked off by the...

Thank you. Your knowledge on these machines is excellent. Thank you again.

Hi. My engine is the pre.eu3 with two hoses / conections in this position. Is it just as simple as drilling a hole to unplug the moulding or would the internals be different on the rad requiring a new one.?

Managed a better picture with sun and camera in right direction.

Taken my rad out to wash out. Find that the bottom teo tubes are for the diesel cooler. One of these has a small preformed hole of 2mm. The other is completely sealed and looks like never had any opening. Is this correct. Recently repaired my diesel cooler it was full of muck. And so were...

Thanks all. Lots to think about. Can deffinetly confirm the ac fan is dead. Got it off eventually after using a dremel as bots rusted up. Fan seized solid. Managed eventually to get the cover off the back but not a pretty sight. Also the fins on the condenser are just dissolving. Touch...

Thank you for the reference numbers will remove the old one and see what can be done with fixing it. Ta.

Tbh had not thought that quick. Always a bit slow off the block. Im the sort of guy who gets a joke from 5 mins ago. You are right. After all it must only be a couple of wires. Investigation tomorrow.... Ta.

Just had a look £140 for a new fan. Ouch. If im doing the job a new one it will be. Oh well. Yes the fins are a bit dubious. I suppose they would stop some air flow through to the intercooler and eventually the coolant rad. At this stage not hoping to change it but may pop out the coolant rad...

Just spraying Salisbury plain mud out the rads of my disco 2. Noticed that the air con fan appears stuck. Can not rotate it with a srewdriver poked in. I am presuming there is no clutch like the compressor and should be free to rotate. Presume its just seized. Is my assumation correct...

New thermostat a few months ago. The hose connections to it were leaking. The new sender was in the top hose.

Took my truck for a proper run since fixing the diesel cooler, and fitting a digital temperature gauge. First time that i had actually monitored the running temperature to such a precise level on any of my vehicles. Went on a run around the new forest in south Wiltshire ,Hampshire and...

My heated rear window had been blowing fuses and whilst i was fitting a remote temp gauge and coolant level sensor which required the removal of kick trim panels around the pedals decided to investigate. Armed with Rave wiring diagrams and connector drawings that had been advised the wise men...

Thats them. Perfect. Did not come up on my initial ebay look. Peobably using wrong spelling knowing me. Appreciated and ordered.

Even though i invested in door trim tools managed to break all bar two on disco 2 rear door.? Anybody know the correct name or code or suppliers for these. 20 years old and think first time its been off. Must be the same for most of the range. Thanks.

Mine is now fitted. And i can confirm no relay required as my paricular sensor obviously works in reverse. Fitted with a little 12v buzzer. Connected to the spare f30 outlet as identified in previous threads by Mr SF. In water no circuit. Raised up out of water a connection is made and...