Search results

https://www.landyzone.co.uk/land-rover/steering-angle-sensor-replacement-guide-with-pictures.312092/page-2#post-5292352

Morning all. Does anyone recognise this head unit, and can an external mic be installed. There is an external one fitted to the car, but whoever fitted it didn't connect it to anything! Thanks MLC

Evening all Does anyone know where I can get a new or used low pressure aircon pipe (without holes in the sides) It goes between the evaporator and joins to a pipe going to the compressor The part number on the sticker says 84423-06 06.02 I suspect this number isn't complete I've attached a...

Other door is the same A pair of wires disappear through from the back of the car to the front of it. But there are no switches or sensors or indicators

Nope, no switches, buttons, lights or sensors (that I can see) I'm reluctant to strip it in case I do damage or mess it up in some way (whatever it is)

Someone had cut the plug off and the wires were just hanging, so I put the 2 sleeved joints on to allow me to connect to the loom again (I copied the other door) I just don't know what the wires going through the door card are for

2002 L322 3.0 tdi I've been fiddling with the rear doors (there's a speaker knackered) and the passenger side window is haunted. Anyone got any idea what the cable I'm pointing to in the photo is for? There's a 2 pin in-line plug / socket break and the two wires are then spliced into two pairs...

I'm impresed, how do you know I have a GM 5L40-E transmission and a New Venture Gear NV225 transfer case.?

Thanks That explains what's missing - which is a clip for holding the "loose" connector, so that's not a worry. These guys do seem to know what they're doing. I've watched a couple of their videos. On this video, he says that an older switch unit (254) can't be used in a newer car in place of a...

Here's a screenshot of one on ebay. I just can't make out what the missing bit is. I don't think it's a plug. I'm guessing that someone has previously tackled the problem and replaced the module and then maybe given up at that point. BTW, the pink edged paper in the files on the lhs of my...

2002 L322 3.0 tdi It's not engaging low speed and hasn't ever done since I bought her, so I'm starting to investigate. I think it's a ZF unit. IID diagnostics doesn't show anything so I'm starting with the hi / low switch, which seems to work ok. But it looks like there's something broken off...

Another wee question for you knowledgeable people. I've replaced the aircon compressor and haven't yet got the system gassed or oiled so I've disconnected the clutch plug to make sure that the compressor doesn't turn until that happens. Probably i didn't have to do that because the pressure...

My IID tool is saying that the temperature demand for the drivers side of the passenger compartment is 5 deg C so that explains why the aircon is constantly demanded 'on'. According to the manual, 5 deg C is way outside the possible demand of between 16 and 28 deg C, Turning the control knob...

All the way there now thanks Bit of muscle and North Sea finest (not necessarily in that order)

Thanks, I'll try persuasion and lubrication (but not necessarily in that order)

That's the one It does rotate a bit, but i don't know how much it should move, I just know that the belt is putting up a hell of a fight against being put on. Is the tensioner openable / repairable?

I still can't get the aircon belt on, so either the tensioner isn't moving enough or I've got the wrong belt The belt I have is a Gates MICRO-V 5PK810 https://www.gates.com/gb/en/search.p.8552-000000-000001.v.8653-10073.html Anyone know if this is the correct one and / or is the tensioner prone...

2002 L322 3.0 tdi Really strange fault with the nearside headlight wiper / washer. The wiper on this side doesn't work but the offside one is ok. I think that means the the fuse is ok and the BCU is sending a signal ok. So I got a replacement which also doesn't work. I made up a jumper loom...

Spot on Datatek, I got the old shaft out and not only is the UJ knackered, the CVs at each end are also stiff and notchy Here are some bits of (hopefully useful) information There's no need to drop the exhaust. The complete shaft slides out towards the front of the car Apart from giving better...

Thank you all It'll be a few days before I can get a replacement, but I'm going to try to get the old shaft out tomorrow. So I have 3 questions 1 - do I really need to take the exhaust off like the manual says I do? 2 - once I get the old shaft out, will the car drive on 2WD without it and will...