Search results

Help needed please, my mot is in the morning Just replaced front pads and adjusted rear shoes all went well, Now there has for a while been a bit of travel on the pedal always better with a second pump, After we finished the job could not get the system to bleed up, pedal right to the floor...

Thanks I will give that a try..

Thanks Rob, ideally an early pickup body type, would only use on occasions maybe the odd country show to promote our firewood business, shame i passed the chance 3 yrs ago was offered just what I was looking for 8k but was not really in a position at the time...Regards Gary

Hi All, I'm looking for a 101 can anyone point me in the direction where I could look for one, please? Many Thanks

Thanks nodge very much appreciated, I think the pump will be a job for the spring, have to put up with the drip when cold till then, but the bushes can be done this weekend I have been spraying them for the last week or so, Just come in from the top do I? double extension bar I thought might...

Fine Thaks for that,I can source a second hand one in that case, do have a good collection of tools, could just do with a quick run down? Like will the rad need to come out ect,Thanks for your help

Yes the D bushes are D in shape and hold the ARB in place.

Hi Folks... I have to get the front D bushes replaced on the Freelander anyone knows a way around this task without removing the subframe? also, I have a leak on the HP pump when the car is cold and goes once warmed up what can I expect will it need changing and is it a hard job?

Yes thanks, they turned up today just waiting on the plates...funny thing is its stopped slipping the pedal is now biting half way up again and not at the top,that's what you get for driving through silty water

Ok looking at the pulleys from the wheel arch, I put the belt over the two top pulleys,w/p, and p/s this holds the belt in place, coming down from my left inside the tensioner, back out and around the crank, once round the crank, this is the strange bit..go up to the alternator make a loop with...

No I cant find it...better try again

yeh Need to find some enthusiast

Thanks guys, some really helpful points, seen a few already just seem to be priced all over the shop

Hi All, Getting geared up to buy a disco 2, Just need to clear the 10p engine and the later 15p does anyone know the changeover year? been advised to steer clear of the 10p but not much around of the later 2003/2004 discos, Any help would be appreciated is the 10p really that bad? and what...

After some quick research, yes they have been known to snap but with mine its running smooth as silk over 1200 rpm, I did move it out of the barn without the pulley on, (to get more light) and was running fine even at tick over So not sure what's going on.

well I finally got there, the belt is on! was a job of patience wich i have very little of these days. However, it sounds as rough as hell still with the new pulley and the belt is flapping around, the noise is coming from the pulley area made sure its tight...could this be crank shalf end...

Thanks arctic, Best picture, and diagram I have seen so far, I took the belt off and put it in the footwell So there is no way it's the wrong belt, as I say it came off that car,before I took it off I had a look around up there to see the layout of the pulleys and was amazed at its length for...

yes pulley was identical, I matched them up before fitting, and the belt is the one that came off the car looked near new, the smaller air con belt has some perishing, so I have a new one, that's a doddle to fit been working o landrovers for 35 yrs and this really is a mystery, thanks for your...

Well no luck at all , it's not just me I have two mechanics and a further two mates and we are all baffled even had my mate take a look and he is a John Deere service engineer, not even close still miles too long Can anyone comment on the Freelander 2 diesel autos are they a step up from the...

I was referring to being nearly 60 with poor eyesight and a big belly.:)