Search results

Hi and thank you both your answers. So to answer your questions, I have always been able to unlock with the key if it was locked with the key since I've had the car (about 3 years) and the alarm has never gone of when i opened the door, thought this was normal. I lock it on the key because...

After losing the unlock microswitch on my old key fob i got a new one and had it programmed to my D2. Now if i lock using the new key and unlock on the key the red light on the dash goes out but as soon as i open the door even a fraction the alarm goes of and i have to put the key in the...

Hi there Sorry for causing confusion but it's the unlock button that was the problem, (I blame old age) . The unlock microswitch is not there but the two small blobs of solder it was connected to are still on the circuit board and it was these i bridged to make a contact and get the doors to...

Just a quick update Got new key on way and have been using bit of wire to bridge contacts to unlock doors (happy hotel guests now). Found someone local with nanocom so as soon as home hope to get it all sorted. Thank you all for your help and advice. Billybones.

Hi The "lock" microswitch is not there at all, when it stopped working i tried to peal back the soft rubber button so i could use something to press the microswitch, as soon as i pealed it back the microswitch fell out of the case.

Hi I removed the sensors to drill a hole in the roof to run some wires through, the alarm was working fine before this.

Apologies for the confusion, my fault, its the Lock button that has fell out, the complete microswitch broke off and came out of a hole in the soft bit of the fob, Lock button is still there and works. Have no nanocom or similar and nowhere near anyone who has one. Trying to find out why it used...

Hi Hope someone can help with this. Vehicle is a 2001 Disco Td5. Away from home at the moment and the "unlock" button on the keyfob has fell out, can still lock/unlock using the key but when i unlock with the key the red light on dash goes out but as soon as i open the door the alarm goes off...

Yep dats true, what threw me was there was three pins on one plane and one on another, expected two to be on the same :p

Hi sorry for being dim but I understand what you mean now, by bridging 30 and 87 power will go direct to fan and it should spin, but there are three perpendicular slots not two, thats what confused me, even in your picture there are three

Sorry i misread your post, can you clarify "the perpendicular cavities" please, I assume you mean the slots the relay pins go into but if it is a four pin relay there will be four slots

Thanks for that graph, From what i can understand then the fan helps with cooling over 110c normal driving, went out for a 60 mile drive today and temp gauge sat in the middle (119c) but when i stopped the fan was not on, which according to your chart it should have been. Is there a way i can...

sierrafery, are you saying not to use the vehicle unless that fan is working ???, what does that fan actually do as i thought it was just for the air-con ???

Hi and thanks for the replys. So an update, the fuse is o.k and the relay clicks, managed to get underneath and spin the fan by hand so thats not jammed. Could see and get my hand on the condenser pipe and not corroded or damp, system was regassed yesterday and was holding pressure so all good...

Thank you, no diagram under fusebox lid but can get one from a breakers tomorrow, where do i find the "electrical library" as used the search on here but nothing shows up ???

Hi and thanks for that mate, just checked fuse and thats o.k, can you tell me how i recognise the relay as no info in owners manual ???.

Hi there Vehicle is a 2001 td5 Auto. Went to air-con shop today to find out why air-con not working and got told (and shown) that fan behind front grill is not working, shop reckons that lack of fan caused compressor to over pressurise and blow the gas out. Now i need to check fuse's etc but in...

Thank you for making it clear, helpful as usual.

Hi Thanks for your explanation and picture, if i read you right there are three options. 1) There will be a blue/black and a black wire somewhere by the trans box made for the job. 2) Run a new wire from the cdl switch to the blue/black wire at pin 7 on the male side 3) Use the unconnected...