Search results

200 tdi in 110 PU with Alisport turbo, I should of used stock but fitting the manifold pipe it is a tight fit. How close does the pipe end up to the frame, I am assuming it is quite close? a friend is doing the modifications, presently the manifold & the adapter pipe from Steve Parker fit tho it...

The 2.5 has a shield on lower pipe to protect the slave I may see if I can fit that also. thnx gives time to come up with something for heat.

Thnx that gives basic idea starter good to protect. the metal ties same as in the package with the tape I assume..

Exhaust tape are they all the same? I will likely manufacture something to shield the starter if you have any pictures of it out of vehicle. thnx.

Yes both clutch piping & starter will need protection just wondering what is best protection? wrapping is one option or a metal heat shield?

Steve Parker suggests moving the clutch hose line mounting point but there are few place to go as limited range of the hose from slave. & basically that are still going to be hot! any suggestions what to do for heat shielding? I am not doing welding a friend is whom is very good slow like a Land...

The PDF I have 90 110 130 Defender supplement lists the 200 tdi no mention of different models. likely it is defender version? 1987 onwards 110 lists a 200 tdi but likely not Disco either. I am wondering how different the design is, the turbo exhaust is different what else is? I also have a...

Thoughts are to cut the center section from existing bulkhead fit that to donor bulkhead with help of welder friend. sometime this summer so the tunnel attachments are intact. take apart heater as you said. mini has taken up time oil leaks.

This sender loosened up leaked oil 1.5 LT I retightened & I should be able to get quite tight. but the last bit of turn I felt a slight give. Not entirely sure if the threads are a match This is a nla item? I am tempted to coat threads in Red loctite unless someone has other ideas? thnx

Clutch for what ever reason reverse was hard to get to work properly of which could be the old clutch master? but it feels quite firm, rebuilt transmission new clutch new slave? looking all this mess over before ripping apart as it needs to go together again in particular if fittings openings...

I may look at rebuilding but on to removing clutch box, pedals & steering. does It matter which comes out first, if I look at it long enough something will seem obvious?

Does the TD5 use the same heater as a 110 PU 1984 would? seems to fit.

Craddock got back to me since the item was still in process for purchase. Yes this is nla everywhere else I checked, oil temperature sensor 2.5 na i think maybe Blanchard sold either a bad unit it had low ohm’s or a 24 V sensor. I now have a working oil temperature gauge that is I believe a Xmod...

I have a 200 disco motor, although do not know what the airbox was from the latch is similar.

Is the forward connector 90 degree a standard fitting? I have two holes for the base but should work, thnx.

I was wondering how where to mount the airbox? is that a 200 tdi airbox?

hello, yes sorry this item is now obsolete,. Lrseries.com I could not get through Craddock paywall. appears this is discontinued by Land Rover?

First fitting of wiper motor with TD-5 wiper stalks they do not move so that is good for fitting. 80DBA168-A011-48EE-B3D6-55484D3C7336 by seaswood, on Flickr

This may be water temperature, I have been trying to get oil temperature gauge to work, it worked before. Did all the tests as Mike explained “ he is great” everything looked good except the sender. Oil temperature sender comes off top of oil filter housing & not the oil pressure switch. PRC4372...

The viscous fan needs a shroud I have been told, I have a 200 tdi in a 1984 PU 110. The are very efficient with a shroud not so much without. have you checked changed the thermostat? I had a small leak sitting in storage, still waiting for time to check which hose.