LR-hobbs's latest activity

My exhaust is ****ed , previous owner had one of those cheap eBay back box deletes , it doesn't seal at all and doesn't join up to my center box like a half inch gap in the join.

That narrows it down as the compressor is brand new I'm talking 1 month old maybe 2. By exhaust leaks are we talking valve block exhaust or the physical exhaust off the engine I personally rebuilt the valve block and there is no leaks from...

I've done a soapy water test all air lines into the valve block ,no bubbles again none on the actual air bags , and no leaks on the air tank fitting also no leaks coming through the dryer All tested with the engine running and I can hear the...

I tried to pull the eas delay timer and the casing came off in my hand leaving the relay motherboard in place . Is there a clip you have to push?

Hi there Little update, the car aired up fine however the rear kept dropping, I've fitted new air bags all round and it's still happening. Do you know of any procedure to diagnose what's causing this? Cheers

I will say I am impressed with the overall condition for such an old car , its the only major rust I've found. Excluding the rear wheel arch where it meets the liner has started bubbling. Apart from that its solid.

I guess it doesn't matter how it's done as long as it welds.

I have bits coming off in my hand So, for the sake of doing things properly and id like to try and learn welding. Il attempt to get a hold of some 1.2 mm then. Cheers

It's a small but brand new mig welder

😂 Il just get some 2mm steel sheets

There seems to be a piece of metal behind that hole that's now loose and when I went under the car it looks like it sits between the exhaust t piece and the boot floor. Possible heat shield? Idk. If I was to go down the welder route , do you...

Just like to revive this post. How's it going?

Hi everyone I was tidying my boot out and found the site below Does anyone know What thickness of metal the floor is made from? And is the floor made of steel? These images are not the bottom of the floor but the sides so they aren't...

I know it's been a while since you posted in this thread but do I need an inpa k-dcan cable ? For it to work on the l322.

Yes almost instantly I get good idle, I am able to raise and lower the car.

Nightmare, atleast I'm getting somewhere.

Got a new cable , didn't even need to install new drivers. Worked a charm

Should be in my bio

I've ordered a new serial adaptor A dedicated FTDI with the driver on a disk , so if this doesn't work then Ive got issues with the car.

it's an old car , the old software an laptops just seem to work better. I presume that laptop would have a dedicated coms port ?

I checked it's windows 11

It's still not having it, I've decided to order a proper FTDI usb adaptor with FTDI driver on a disk. I swapped my usb adaptor to a prolific one and got a string of 28s and 80s rather than the pp. So I believe it to be the adapter.

I cannot for the life of Me , delete the driver , everything I've done it just bounces back auto update is turned off so I'm not entirely sure what I've done wrong. Sorry to be a pain , but could someone give me a dummy's guide to deleting the...

Just to make sure I don't do this wrong which driver type do I install

Right I understand, hopefully this works. The cable was an eBay cable with adaptor £17 or so came with a free dvd copy of rave which is a bonus.

I uninstalled the driver and the ports section completely disappeared. Restarted the computer and still gone.

Cleaned the OBD2 port , there is some greening on the face of it and the entrance metal is also green. Still getting the same fault. I have tried multiple ports on my laptop makes no difference. Not sure what else to try

I updated the driver using the hardware updater, and Installed FDTI. I do have the correct driver software on my desktop , I click set up go throught it and nothing happens

Laptop is brand new and I believe it's windows 10 , the cable I bought online and received it yesterday. I did have issues changing the drivers and I'm not entirely sure I have done it correctly. If there is corrosion in the obd port , how do...

Hello everyone I am trying to get eas unlock to work , I have the correct drivers and cable however when I try to initialize I just getting PP in the Rx box and can't use any functions Thanks