Hi you should have a look at Donegal overlanding on Facebook. They are from up that way but travel around the country.

Hi folks, I'm planning on rebuilding my 1989 110 hard top/van and considering rebuilding as a 130 DCPU or at the very least a 130 single cab. I am not buying a 130 chassis old or new as I need to keep the current vehicle chassis number for vintage reasons. I had intended just rebuilding as a...

I'm just after putting copper grease on the pivot point and it has stopped the screech for now. In the likely event of it screeching again I'll be changing the shoes. Ferodo was mentioned before.

Help please. My rear brakes are squealing quite loudly. They are drum brakes and no matter if I have the shoes tight or loose they squeal. I've chamfered the edges of the brake material, sanded the drum and shoes lightly and ensured the leading shoes to the front. They are on a year and have...

Hi. Did it work? I have the same problem.

Update: I put a 22 tooth drive in and it brought it closer to correct at just 5% over reading. Close enough for me.

Yea that's the math I done too. Apparently there is a formula but needs gear diameter not just number of teeth. But if the gear drives are the same diameter then you are probably right. I'll get the 22 tooth and see what happens.

Was chatting to an engineer buddy who says the same that more teeth should slow down the Speedo bringing it inline with correct speed. There is currently a blue 20tooth in it so will pick up a 21 or 22 tooth. Just trying to figure out which one now. Knowing my luck I'll pick the wrong one. Not...

No worries. I can only find the 4 sizes of gear drive. Blue, red, yellow and green. The wheels are 31x10.50R15 very close to the standard size I think

This is for the TD5 on. I did find this though. Not sure if it would work need to check. http://www.marks4wd.com/speedo-correction/mfk1468b.html

Hi folks, My speedo is currently out showing 70mph when actually traveling at 60mph on the GPS. Thats 17% over reading. Its been like this for a good while and I had simply marked the speedo with tipex on the speed limits. I had looked into this problem and thought I might have the wrong speedo...

All done and running nicely. Had trouble getting the fuel line parts sorted but a local garage that used to dabble in Land Rovers came up trumps with the parts. Ended up using the original TD air filter housing it was simpler to use it than fiddle around with the new one.

So I've finally gotten the 200tdi mounted into the 110. Just sorting out the mismatch of fuel pipes and air. I had started to paint bits and pieces from the engine but the paint needed to be sprayed and I just haven't got the time or area to spray paint. So the pulleys, alternator and a few...

Sold

Thanks for that. I'll keep most of that and do some checking of part numbers to see what else may come in handy. Just ordered my engine crane and paint for the engine might get to do a bit more this weekend.

What parts are actually worth keeping from the 19J that I can keep as spares for my 200tdi? Alternator, Starter, Lift pump anything else??

Update: So I have started working on the 200tdi engine and started to strip some of the bits off it to give it a good clean and probably even paint it. Any suggestions on how to tidy up the exhaust manifold? Sand blast and engine enamel? Ordering an engine crane instead or renting one so I can...

I honestly don't know where it is fitted but there is a member who had said "Looks like the in wing petrol tank off my rangie, it's there cause it's LPG under the back" in a thread I had posted to find some info about it Thread was : Recognize this Fuel Tank??

First things first I am selling this item from Ireland I'm selling a aluminum fuel tank that i had hoped to use in my Defender but won't need now. The tank (from my best google search and this forum) is for a Range Rover Classic and Mk. 1 Discovery and was intended as a smaller petrol tank...

I used those strikers you have in the link for my doors which are Lift up handle doors with wind up windows.