Your Halford's 12 pointers should be okay

Started with Nessie because of her NES registration The rest just sort of followed on

Thanks James. The switch was removed from the car before the checks were made. But thinking about it there must be 2 different off/on situations. The switch has only 2 positions, depressed or non depressed. If both solenoid and reversing lights can be activated at the same time then it would...

Disco 1 1995 V8i Automatic Can anyone tell me if my start inhibitor switch is really knackered or not? The car will start in any gear not just “P” and “N” so something is wrong The reversing lights don’t work either but I can’t be sure yet that the switch is the cause of this. A continuity...

Thanks everyone I previously had only WD40 but have just been out and got a can of GT85. I'll give every thing a good skoosh and try out the methods described. From the 2nd video it is now apparent that the push rod should be sliding within the collet without the collet itself moving...

Disco 1 1995 V8i Automatic I have been searching the posts and my problem seems to be fairly common but I can’t get the information that I am after. The transfer lever was stuck (I suspect through lack of use) but I have exposed it from inside the car and managed to get the High-Low ratio...

It might fit but I think you could fail the MOT because of it Doesn't the 3 door seat slide forward and hinge to allow access to rear seats? The 5 door seat only has slide and rake adjustment

Thanks again

Sorry I forgot it was the clutch you were referring to

I found when bleeding a Ford Fiesta some years back with an Eezi Bleeder I got better results if i idled the engine when bleeding. I dont know if it will work on a Disco but was planning on trying it after I have installed new brake calipers on my Disco 1

Many Thanks for the input guys. Sorry for the delay in responding but work had to take priority I managed to get the nuts off with a set of water pump pliers but one really was quite tight. I will get a proper socket to do it back up properly.On torquing back up my manual says 13. Fit hub...

I'm doing a similar job on my V8 but I'm having trouble with the inner nut. Nothing I have fits and I am a wee bit concerned about getting it torqued back up correctly. Can anyone advise the correct sized socket. It measures 36-37mm across the flats GDM - I've recently been ordering parts...

First Disco I ever drove was my brother in law's TDi (G reg ) and was to pull a caravan to France Once I got started the thought was going through my head "Why stop in France - this thing will go anywhere" Just loved them ever since

It was linked back to supplemetary reversing lights and reversing camera. No apparent connection between it and the lamp in question but the set up didn't work anyway so who knows? Since I started looking in around the back of the dash - see my post re aerials - I have discovered a lot of...

Not quite what I had in mind - but thanks anyway

1995 Disco Mk 1 V8i Automatic LPG A previous owner had fitted a radio/CD/ DVD player and presumably because the original aerial had been snapped off at the base opted for an internal windscreen one. The radio reception was rubbish so I decided to replace it a normal radio/cd player...

I am having a problem with reversing lights on my 1995 Disco Mk 1 V8i Automatic LPG One of the previous owners has fitted a triple NAS rear light cluster and appears to have attempted to fit a reversing camera and has messed up the original wiring. The upper rear cluster was not wired...

1995 Disco 1 Roof gutters are badly corroded. Can they be replaced or any tips on how to repair them?

Thanks - I was kinda hoping there was an easier way

New to me 1995 Disco 1 V8i (LPG) Automatic. First thing that needs to be done is the usual oil change, plugs etc However Haynes manual reckons that changing the automatic transmission fluid should be left for a dealer. Is that right? I am sure I saw Edd China doing it without too much...