So yesterday I made a purchase :D


t002.jpg
 
Pah, tis easy tbh, especially if it's a case of just bodging your car together.

My advice, sills first, they're the easiest so by the time you get to the tough stuff you'll be quite competent.

Get a few bits of 2mm steel, weld them together, weld that to that etc, it's easy cos it's thicker than 1.2 (car panel) but not too thick for you not to get the feel of it.

Cheers :)
 
I've been having a practice on some scrap panels but don't have a manual with the welder so I'm a little lost what to do with the three white switches! I think I'll take your advice, just got to ask to borrow my mates pit as I don't fancy welding lay on my back!
 
Welding on your back is bloody 'orrible!

Yeah not sure how to work out them switches.

My welder goes like this:

1 Min
2 Min
1 Max
2 Max

Yours is more complex though cos its got that A in there!
 
Welding on your back is bloody 'orrible!

Yeah not sure how to work out them switches.

My welder goes like this:

1 Min
2 Min
1 Max
2 Max

Yours is more complex though cos its got that A in there!

A welders just not a welder without an "A" in there, yours must be an imitation!! :D
 
There's a bit on there that reads "push A for positions 2-3". So I'm thinking 1 is 1, A-2 is 2 and A-3 is 3. So mine in the picture is set on 2-MIN, that make sense?! So there's position 1-3 then min-max. Which means I can use the guide in the 150TE instructions as the dial is just 1-3 and then min-max.
 
So yesterday I made a purchase :D


t002.jpg

Hey thats similar to mine but I dont have the A button so cant help on that.

Nice helmet too - I am looking at upgrading my auto helmet to a nice skull painted one :) Ummmm

Welding is easy once you find a nice setting. Plenty of parctice and that will build your confidence. I am happy to tackle anything now where as when I started I was very apprehensive

Could A be for Ali when using special wire????
 
There's a bit on there that reads "push A for positions 2-3". So I'm thinking 1 is 1, A-2 is 2 and A-3 is 3. So mine in the picture is set on 2-MIN, that make sense?! So there's position 1-3 then min-max. Which means I can use the guide in the 150TE instructions as the dial is just 1-3 and then min-max.

Yes. Position 1 is 1 alone, to use settings 2 and 3 button 1 has to be on the A position
( I have this welder at home):cool:
 
Yes. Position 1 is 1 alone, to use settings 2 and 3 button 1 has to be on the A position
( I have this welder at home):cool:

Thank you, you said what I was trying to say but without going on and on and on and on and on and on.........
 
Hey thats similar to mine but I dont have the A button so cant help on that.

Nice helmet too - I am looking at upgrading my auto helmet to a nice skull painted one :) Ummmm

Welding is easy once you find a nice setting. Plenty of parctice and that will build your confidence. I am happy to tackle anything now where as when I started I was very apprehensive

Could A be for Ali when using special wire????

I was going to get an eagle mask that was £60 then I saw this one for £70 and just had to buy it!! Its exactly the same mask but a different pattern....I guess a black one would be £50!

That's what I'm doing at the moment, trying to figure out the best settings on scrap pieces. Once I've done that I'll spend an hour or two practicing for neatness then get stuck into my disco!
 
Predation is your best friend. Always, without exception go back to clean full width metal. Trust me you will always end up there even after you have tried cutting corners. So best go back to fresh metal straight away.

Next use a piece of cardboard to make your templates for patches. It is much easier to trim cardboard than metal sheet and less noisy. I made several templates up then I could get the most out of my patching sheet and then also, I could just spend a half hour welding without interruption. This time helps learn quicker as you get a feel for the welder.

Always chamfer thicker metals so you are welding in a groove as this promotes better penetration.

Once welded I strongly suggest seam sealer. I got mine off of eBay and the best is tiger seal. DO NOT USE BATHROOM SEALANT. I have no leaks at all through any of my welds and it is this water penetration that rots the metal out, hence why rot is always at the edges.

Finally prime with zinc primer or good old red oxide.

Once sealed
 
Thanks for the tips guys, I've taken them all on board. Been having a play with the welder today on some scrap pieces and slowly getting a feel for it. Still not as consistent as I'd like to be, but a big improvement. Tomorrow I'm going to try and get a bigger bottle of argon/co2 as I only have the little disposable co2 at the moment.

A bloke I know has told me to use "zinc tech panels" for patching but I've never heard of them! Any one shed any light on these and where to buy them from? All the other panels will be from yrm or easy on panels on egay.
 

Similar threads