danny6801 · Mar 6, 2017

I never seem to find them at that price or even close enough to even go and have a look at them.

Marmaduke · Mar 6, 2017

danny6801 said:
I never seem to find them at that price or even close enough to even go and have a look at them.

Bugger it failed

I was hoping it would be catastrophic but I've fixed the lights, off to craddocks tomorrow for a timing kit and front hub bearings. Then to buy a lower end engine for a replacement sump.I'm off work for 11 days so I'll swap the insurance over and run it for a week to decide but discos are a way nicer place to be than tratters.

Marmaduke · Mar 6, 2017

I'm planning on taking it to Wales for a play on Saturday

Magicgrotto · Mar 6, 2017

Fuses & Bulb bi chance ??

Marmaduke · Mar 6, 2017

Magicgrotto said:
Fuses & Bulb bi chance ??

Just a bad earth, I gave it a slap and it came back on

Magicgrotto · Mar 6, 2017

Marmaduke said:
I'm planning on taking it to Wales for a play on Saturday

Don't F/in break it yu only just got it !!

james6546 · Mar 6, 2017

JimS said:
Is that the twin turbo 3000GT or the normally aspirated? Looks clean and nicely original

Well in theory its a 1995 3000GT Twin Turbo with 86k miles, but I bought it with the engine in bits after a massive overheat and am slowly putting it back together with my limited mechanical knowledge!

And yes, it is rare that it is 100% standard, minus the painted wheels

Magicgrotto · Mar 6, 2017

@james6546 You could always let the tyres down & use it as a ramp !

james6546 · Mar 6, 2017

Magicgrotto said:
@james6546 You could always let the tyres down & use it as a ramp !

It's pretty low. I'm actually really enjoying not having to stand on a box to work on the engine... though that may be because it's in the garage!

Marmaduke · Mar 6, 2017

danny6801 said:
I never seem to find them at that price or even close enough to even go and have a look at them.

I do you a good deal on it

lynall · Mar 6, 2017

Marmaduke said:
That'd do, bit rougher than mine though

D.I.S.C.O

Magicgrotto · Mar 6, 2017

Have you found out why c/l int workin yet ??

danny6801 · Mar 6, 2017

Marmaduke said:
I do you a good deal on it

How good a deal lol.

Marmaduke · Mar 6, 2017

Magicgrotto said:
Have you found out why c/l int workin yet ??

Fuse had gone and the nsr door motor needs looking at, thanks for the heads up though

Magicgrotto · Mar 6, 2017

You can check motor with 12 volts (door card off) If that dunt work brushes in motor crackerd New motor of the bay about £ 1.50 ish ! but you have to put your gear wheel on !

Marmaduke · Mar 6, 2017

danny6801 said:
How good a deal lol.

Probably not cheap enough for you

Magicgrotto · Mar 6, 2017

@Marmaduke Eltop Electonics £1.32 MR01 motor

Marmaduke · Mar 6, 2017

Magicgrotto said:
@Marmaduke Eltop Electonics £1.32 MR01 motor

Cheers for that. If I put the fuse back in the motor will pop the button up and down but it sounds like the motor keeps going for another few seconds so it might just need adjustment. I wouldn't mind but when I last broke a discovery I weighed all the doors and internal gubbins in

Magicgrotto · Mar 6, 2017

You should NEVER do that !!!!!

If it's working then yes prob needs adjusting

Co-Pang-Yang · Mar 6, 2017

Got a door lock that don't work on mine.
Still don't understand how you fix them

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Well-Known Member

Similar threads