timtheenchanteruk
Well-Known Member
got a nice wind free corner, getting the sun, but no wind, so im getting on with making a swing away bike carrier since used carriers go for silly money when I'm gonna cut some of it up anyway.
got a couple of old school tables with decent lengths of square tube im recycling
got a couple of old school tables with decent lengths of square tube im recycling
defender11069
AKA Mr cool...
got a nice wind free corner, getting the sun, but no wind, so im getting on with making a swing away bike carrier since used carriers go for silly money when I'm gonna cut some of it up anyway.
got a couple of old school tables with decent lengths of square tube im recycling
best thing's in life are free.
pontyslapper
Brought a Landy to LZ11. Yay!!
Bruv came over and we ended up drilling a new hole for the EGR valve delete as the bloody drill bit snapped half way through!!
That sorted I thought I'd check the coolant - little low, so topped it up, and started Drover up, started to loosen the plastic plug on top of the thermostat housing to bleed it, and the bugger came away in me hand! Arse - so now I have to hope that I can get one tomorrow and SWMBO ain't to p'eed off with me for needing to use her car!
Pondering is it better to go brass or stick with plastic?!? There's only really pocket money in it - so I might stick with plastic but get a few!
That sorted I thought I'd check the coolant - little low, so topped it up, and started Drover up, started to loosen the plastic plug on top of the thermostat housing to bleed it, and the bugger came away in me hand! Arse - so now I have to hope that I can get one tomorrow and SWMBO ain't to p'eed off with me for needing to use her car!
Pondering is it better to go brass or stick with plastic?!? There's only really pocket money in it - so I might stick with plastic but get a few!
Nathan1992
Member
Removed the seatbox, floor and transmission tunnel from mine before removing the gearbox!
Nathan1992
Member
Oh and I also fitted my MT tyres to my dads Landy!
blue beasty
Leaks an prone to bits dropping off
Been tinkering with the carb settings........bloody fiddly things, I'll never understand them :doh:
Pikey
Dummy Ejection Facilitator..
Get ya self to plumbase (other suppliers are available) & get ya self a Brass or iron blanking plug. I've got an Iron one, with a square lug on the top. BIt of ptfe tape and the jobs a good un.
Pikey
Dummy Ejection Facilitator..
There's a vacuum gauge in the workshop. can't go wrong setting up ya carb with one. Course yu need to know how to use one..
Oh BTW, went to ALDI today & got a combined water seperator/filter/oiler/regulator for the air compressor. Comes with Air hoses anorl. A snip at £19.99. They had a spot blaster tool & a air cutoff tool for £9.99 each as well. But Minty was watching so couldn't get em
jai_landrover
Well-Known Member
The 80 is on the trailer and I have put axle stands under each wheel and I might be able to get under it to weld some bits if I find some board to lay on.
Crank pulley is slipped back on and it on charge
Need to sort lots but on the plus side the evenings are getting lighter and work can start again
Crank pulley is slipped back on and it on charge
Need to sort lots but on the plus side the evenings are getting lighter and work can start again
monkfish24
Well-Known Member
Well after all the electrical faults, the dash is all back together now, still no heater but that can wait til after MOT time. Just a new washer pump needed, some welding and fog light to sort out and it may well be mot time!
monkfish24
Well-Known Member
broke both rear shocks at yarwell today and then dislocated both rear shocks shortly after then think i may have broke me thumb replacing the shocks but had massive fun and seriously impressed with the standard ol' girl
if you need a hand, I'm just down in Helston.
discomark10
Well-Known Member
I got brass ones.. would never go back!
Turboman
Mab An Gov
Cambridgeshire?
