trax

.

Events Planner

• Oct 15, 2013

• #22,141

discomark10 said:

Don't forget to get a video!

Click to expand...

and a fire extinguisher !

 

Chrisw8

Well-Known Member

• Oct 15, 2013

• #22,142

done some prep work for refitting swivel housing etc

 

Dr_evil

Banned

• Oct 15, 2013

• #22,143

made it run , found one last leak and wired up the fuel sender

 

Lazy Landy

New Member

• Oct 15, 2013

• #22,144

I have seam sealed round the welds on the footwell I've welded in and cleaned years of underseal, oil and crud off my steering box column ready for the new top bearing, hopefully arriving tomorrow.

 

blue beasty

Leaks an prone to bits dropping off

• Oct 15, 2013

• #22,145

New track rod end fitted, took a little play out the front near-side wheel bearing and swivel pin. One shackle bush to do and she's ready for the mot.

Made a plan for picking up the ambulance...

 

Dr_evil

Banned

• Oct 15, 2013

• #22,146

blue beasty said:

Made a plan for picking up the ambulance...

Click to expand...

Does that involve taking the train to pick it up then calling the RAC

 

blue beasty

Leaks an prone to bits dropping off

• Oct 15, 2013

• #22,147

Dr_evil said:

Does that involve taking the train to pick it up then calling the RAC

Click to expand...

Involves taking some hub seals, a full compliment of fluids and filters and a pre-booked mot

 

Dr_evil

Banned

• Oct 16, 2013

• #22,148

oooh its a good one then



I'm off to mess with the V8's wiring and timing, need to order a new barrel too…….pulled a muscle in my back so probably wont be fitting the exhaust til tomorrow

 

Paul D

Old, nackered 'n broke, but the Landy is fine . :)

Events Planner

• Oct 16, 2013

• #22,149

Loaned it to the missus ...

Took her Mondeo for an MOT, failed on a lower front suspension ball joint .. so that's the 'tapping' she said she could hear then!!

Ah well, new one bought and car stripped as far as I can till me decent tools return in the back of the Disco!!

 

Dr_evil

Banned

• Oct 16, 2013

• #22,150

About to go mess with the timing…..again

 

the_wolf

Well-Known Member

• Oct 16, 2013

• #22,151

Used it to take some stuff to the tip and marvelled at how much warmer it is with a truck cab on

 

Dr_evil

Banned

• Oct 16, 2013

• #22,152

Fecking typical just sorted out the battery cable with a nice new lug and it starts raining…...

 

concal

New Member

• Oct 16, 2013

• #22,153

Not today but yesterday started work at 6 finished at 3 then disco straight in garage at work and replaced swivel seal and replaced bearings finished at 11 last night (fecked isn't the word)
Only the other side to do now!!!!
Bastid of a job anorl

 

Dr_evil

Banned

• Oct 16, 2013

• #22,154

Fitted the exhaust, sorted the idle (more or less) and sorted a bit of the wiring

 

Lazy Landy

New Member

• Oct 16, 2013

• #22,155

Sprayed some primer on my new footwell, starting to get some ware if I get a little bit done every night. Half an hour workshop tidying now.

 

Pikey

Dummy Ejection Facilitator..

• Oct 16, 2013

• #22,156

batesy16 said:

erm wasn't the easiest thing to do - had to take green filter out completely so they had to be broke into small pieces

superglue is also handy as the green filters hold in the bulb holder, so these had to be fitted back on

Click to expand...

Should have just fitted white leds they turn the dash blue with the green filters intact.

 

Pikey

Dummy Ejection Facilitator..

• Oct 16, 2013

• #22,157

Discovered why me brakes have gone to ****e. SErvo Vacuum Pump is spewing Oil everywhere. But I've sourced a replacement so hopefully all will be sorted tomorrow.

 

Markieboi

Member

• Oct 16, 2013

• #22,158

Primed up my new wheels ready for paint tomorrow afternoon.

 

DJ Xan

Active Member

• Oct 17, 2013

• #22,159

washed it

 

Dr_evil

Banned

• Oct 17, 2013

• #22,160

Finally sorted the engine!