quote=gemsdad;2434863]just tell sue to use a gas axe,then weld a new one back in.:D:D[/quote]

stutab said:
Now thats a good idea :D use oxy propane, it cuts better;)
Click to expand...


That would definately have to wait a few weeks, I haven't learned to weld yet, but it is on my list:D. Apparently I have to practice on a van before I am allowed near a Landy :D

I did go shopping today as well, I bought my Landy a Disklok, really cheap from the car alloy wheel shop :D Daughter was not happy as we went for alloys for her car.
 
suew said:
quote=gemsdad;2434863]just tell sue to use a gas axe,then weld a new one back in.:D:D
Click to expand...




That would definately have to wait a few weeks, I haven't learned to weld yet, but it is on my list:D. Apparently I have to practice on a van before I am allowed near a Landy :D

I did go shopping today as well, I bought my Landy a Disklok, really cheap from the car alloy wheel shop :D Daughter was not happy as we went for alloys for her car.[/QUOTE]

You need to cut it up before you can weld it back together.

Always better looking after a landy than chaving up a car :D
 
Put engine and clutch in then tried gearbox but block of wood keeping engine at right height was in the way so wouldn't go in all the way. Splines locked up though so going to swap the wood for a bottle jack tomorrow
 
Dr_evil said:
Put engine and clutch in then tried gearbox but block of wood keeping engine at right height was in the way so wouldn't go in all the way. Splines locked up though so going to swap the wood for a bottle jack tomorrow
Click to expand...
Couple of bolts with the heads cut off and threaded into lower bolt holes. or threaded bar abiut 6" Long. lines gearbox up perfectly.
 
redhand said:
Couple of bolts with the heads cut off and threaded into lower bolt holes. or threaded bar abiut 6" Long. lines gearbox up perfectly.
Click to expand...

Oh it was fine going in it was just the block of wood I was using to hold the engine up got in the way so going to get a bottle jack and prop up the sump end with that to get the height right :) then feed in by hand with crane supporting
 
nice new flat wipers and a bee sting aerial, well i fitted new wipers even though i need a wiper motor cause the wipers just stop any where they feel like it in the screen. atleast when they are deciding where to stop they dont squeek about it anymore.
 
Today I made a start on making my heavy duty rear bumper. The two lengths of tubing I got of a mate ( I got 4 off him two I've already used to make rock sliders ) they already had the two bends in them.
In one of the picture you can see the black bit welded on the top that is part of the old frontera rear bumper lol
A5654058-950C-4F1E-9905-37759409CCA7-464-00000065F71CE62B.jpg

FA3107FF-656F-4B0B-A413-665DA033330B-464-000000660A97ABBE.jpg


Old picture of the rock sliders

F190B894-AB5D-40D7-B011-27BC7D634C1F-14953-000002A5222D8EFF.jpg


So one heavy duty bumper and two rock sliders all for £20
 
Last edited:
went to go and sort out the gearbox………..tried for an hour then decided to take the clutch off and have a look at what was up as it was leaving about an inch gap all the way round no matter what I tried

turns out the clutch was put on about 2mm too far to the right so the spigot bush and input weren't lining up right, one side of the bush had a few small dents in it so I've given up until next weekend, got the engine in though so pleased with that and going to bring the MIG over next weekend I reckon and give the bulkhead a blast
 
Dr_evil said:
went to go and sort out the gearbox………..tried for an hour then decided to take the clutch off and have a look at what was up as it was leaving about an inch gap all the way round no matter what I tried

turns out the clutch was put on about 2mm too far to the right so the spigot bush and input weren't lining up right, one side of the bush had a few small dents in it so I've given up until next weekend, got the engine in though so pleased with that and going to bring the MIG over next weekend I reckon and give the bulkhead a blast
Click to expand...

so, who fitted the clutch then ?
:confused:
 
I put it on last night, think the clutch tool may have wanted another layer of tape putting round it so my fault on that

got a spare spigot anyway (ordered two) so will try again next weekend as I cba now
 
Dr_evil said:
went to go and sort out the gearbox………..tried for an hour then decided to take the clutch off and have a look at what was up as it was leaving about an inch gap all the way round no matter what I tried

turns out the clutch was put on about 2mm too far to the right so the spigot bush and input weren't lining up right, one side of the bush had a few small dents in it so I've given up until next weekend, got the engine in though so pleased with that and going to bring the MIG over next weekend I reckon and give the bulkhead a blast
Click to expand...

so you fit it by eye then? did you not have a pilot tool????????
 
Dr_evil said:
I put it on last night, think the clutch tool may have wanted another layer of tape putting round it so my fault on that

got a spare spigot anyway (ordered two) so will try again next weekend as I cba now
Click to expand...

well we will all be on "spaceshipzone" by the time this is up and running :D
 
I used the pilot tool was an ancient sykes pickvant one and slightly bent so that probably didn't help. May see if the local landy garage has an R380 input shaft they've chopped off to use as a guide and ask nicely if I can borrow it as it'll be miles better than using the knackered old one
 
You must log in or register to reply here.

Similar threads

B
defender 2.4 puma reverse light switch
Replies
4
Views
852
BEASTIE 90
B
MinionKing
Freelander 2 (LR2) Freelander 2 Torque pull
Replies
11
Views
675
coltron1
C
stumpyj
TD5 Fuel line to fuel pump clip
Replies
10
Views
1K
Alan Henry Crossley
A
Padda.116
300tdi disco 1, new head gasket oil leak!!
Replies
10
Views
959
Padda.116
Padda.116
Knappster
Shot-blasting steel wheels
Replies
9
Views
1K
Knappster
Knappster